All users of Whirlpool washers are informed about a very useful function – the electronic self-diagnosis system. That means that in the case of failure machine determines a breakage and displays information in a form of the code. With the help of this option, you can cope with a problem by yourself without calling a repair service. So it saves not only money but also a precious time.
On this page, you can see the table filled with the error codes of Whirlpool washers. Each code diagnosis the certain issue and suggests the possible ways of its solution. For example, it may be a failure in the water supplying system, no draining, slow heating, breakage of the heater, engine malfunction etc. Many breakages can be repaired without any difficulties. It is useful to note that almost all washer`s models are characterized by common error codes. It is easy and doesn’t lead to confusion.
Whirlpool WFC7500VW Washer Error Codes
ERROR CODE | MEANING | SOLUTION |
---|---|---|
“A09” on display | Water Inlet Problem—no water or insufficient water supply | If this error occurs, the system will pause. Unplug washer or disconnect power. Check the following: Are water faucets completely turned on? Are screens at inlet hose connection to washer clogged? Are water inlet hoses kinked? Are water inlet hoses frozen? Plug in washer or reconnect power. Press and hold START to continue the cycle or press and hold CANCEL/DRAIN to cancel the cycle. If the problem remains, call for service. |
“A10” on display | Drain Problem | Unplug washer or disconnect power. Check the following: Is the drain hose kinked? Is the drain hose frozen? Is the drain hose clogged? Is the drain hose more than 55" (1.4 m) above the floor? |
“F” Variables [F01 - F30] | Electrical Problem | Switch knob or press and hold START to cancel the cycle. Select DRAIN/SPIN if there is excessive water in the washer. Re-select cycle and press START. If the problem remains, call for service. |
Whirlpool WFW9050XW Washer Error Codes
If you experience | Possible Causes | Solution |
---|---|---|
Sd (Excess suds) appears in display | Excessive suds in washer. Washer is running a suds reduction routine. | Allow the machine to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions. If the dial is flashing, reselect your desired cycle using a cold wash temperature, and press START/PAUSE. Do not add detergent. |
F8E1 (long fill - no water supply error) appears in display | Check for proper water supply. | Make sure hot and cold inlet hoses are not reversed. |
Both hoses must be attached and have water flowing to the inlet valve. | ||
Both hot and cold water faucets must be on. | ||
Inlet valve screens on washer may be clogged. | ||
Remove any kinks in the inlet hose. | ||
Press START/PAUSE once to clear the code. Then press START/PAUSE again to restart washer. If code appears again, call for service. | ||
F9E1 (drain pump system error) appears in display | Check plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 4.5" (114 mm). | Check drain hose for proper installation. |
Make sure the drain hose is not kinked, pinched, or blocked. | ||
Remove any clogs from drain hose. | ||
Use drain hose form and securely attach to drainpipe or tub. | ||
Lower drain hose if the end is higher than 96" (2.4 m) above the floor. | ||
F-- E-- code (Washer problem) | System error code. | Press POWER to cancel cycle and clear the code. Then press POWER and select DRAIN & SPIN if there is excessive water in the washer. If the code appears again, call for service. |
Whirlpool W10254493A Washer Error Codes
If you experience | Possible Causes | Solution |
---|---|---|
Sud (Excess suds) appears in display | Excessive suds in washer. Washer is running a suds reduction routine. | Allow the machine to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions. |
F08 followed by E01 (water supply error) appears in display | Check for proper water supply. | Both hoses must be attached and have water flowing to the inlet valve. |
Both hot and cold water faucets must be on. | ||
Inlet valve screens on washer may be clogged. | ||
Remove any kinks in the inlet hose, | ||
Press POWER once to clear the code. Then press POWER again to restart washer. If code appears again, call for service. | ||
F09 followed by E01 (drain pump system error) appears in display | Check plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 4 1 ⁄2" (114 mm). | Check drain hose for proper installation. |
Make sure the drain hose is not kinked, pinched, or blocked. | ||
Remove any clogs from drain hose. | ||
Use drain hose form and securely attach to drainpipe or tub. | ||
Lower drain hose if the end is higher than 96" (2.4 m) above the floor. | ||
Not using HE detergent or using too much HE detergent. | Use only HE detergent. Always measure detergent and follow manufacture’s directions based on load size and soil level. | |
F05 followed by E02 (door will not lock) appears in display | Washer door not locking. | Press POWER to cancel the cycle. Make sure the door is closed completely and latching. Check for items in the washer drum that may be keeping the door from closing completely. |
F07 followed by E01 (motor drive error) appears in display | Motor is having difficulty turning the drum. | Washer is tightly packed. Remove some items. |
“rL” (remove load) appears in display | Load detected in drum during Clean Washer with affresh® cycle. | Remove items from drum and restart Clean Washer with affresh® cycle. |
Washer making error beeps | Door has not been opened and closed for at least 3 cycles. | This code may appear when the washer is first turned on. Open and close the door to clear the display. |
Washer beeps when START/PAUSE is pressed | Door not closed. | Close the door completely. |
F## E## code other than as described above appears in display | System error code | Press POWER once to clear the code. Then press POWER again to restart washer. If code appears again, call for service. |
“Int” (interrupted) appears in display | The cycle was paused or cancelled. | The washer can take 20 to 30 minutes to stop spinning and drain and will display this error code during that time. Touch POWER once to clear the code. Then touch POWER again to restart washer. |
Clean Washer LED flashing at end of wash cycle | The washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer with affresh cycle. | Run the Clean Washer with affresh cycle. If the Clean Washer with afresh cycle is not turned on, the LED will stop flashing at the end of a wash cycle after running 3 more regular wash cycles. After 30 more wash cycles are completed, the Clean Washer LED will again flash at the end of a wash cycle as a reminder. |
Whirlpool WFW9550WW Front-Loading Automatic Washer Error Codes
ERROR CODE | MEANING | SOLUTION |
---|---|---|
"Spin" and "Wash" (HT "Rinse" and "CycleComplete") illuminated or "F20 (or FH)" on display | Water Inlet Problem—no water or insufficient water supply | Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power. Check the following: Are both hot and cold water faucets completely turned on? Are screens at inlet hose connection to washer clogged? Are water inlet hoses kinked? Are water inlet hoses frozen? Plug in washer or reconnect power. Re-select cycle and press START. If the problem remains, call for service. |
"Spin," "Wash" (HT "Rinse,""Cycle Com-plete") and "Add a Garment" illuminated or"F21 (or F02)" on display | Drain Problem | Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power. Check the following: Is the drain hose kinked? Is the drain hose frozen? Is the drain hose clogged? Is the drain hose more than 96" (2.4 m) above the floor? Plug in washer or reconnect power. Re-select cycle and press START. If the problem remains, call for service. |
“SUD” | Suds Routine | When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. “SUD” is displayed during rinsing to inform you that Suds Routine was activated. Use only HE (High Efficiency) detergents. |
“F22” | Front door lock | Select PAUSE/CANCEL twice to cancel the cycle. Check the following: Is the washer door firmly shut? The door must be completely closed for the washer to operate. The door may look closed, but may not be latched. Open the door and close firmly. Were you washing a large load? Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to tumble freely. An tightly packed basket may keep the door from shutting completely. Reduce your load size if needed. Press POWER and select START |
“F” codes other than F20, F21, or F22 | Select PAUSE/CANCEL twice to cancel the cycle. Select DRAIN/SPIN if there is excessive water in the washer. Re-select cycle and press START. If the problem remains, call for service. | |
Any other Status light combination | Electrical Problem | Select PAUSE/CANCEL twice to cancel the cycle. Select DRAIN/SPIN if there is excessive water in the washer. Re-select cycle and press START. |
Whirlpool WTW8200YW Washer Error Codes
If you experience | Possible Causes | Solution |
---|---|---|
oL (overloaded) appears in display | Load too large. | If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE. |
uL (unbalanced load) appears in display | Load not balanced. The washer is running a load-balance correction routine. | Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE. |
LF (too long to fill) appears in display | Washer taking too long to fill. Drain extends more than 4.5" (114 mm) into standpipe. | Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. |
Ld (too long to drain water) appears in display | Washer taking too long to drain water. Drain extends more than 4.5" (114 mm) into standpipe. | Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. |
Lower drain hose if the end is higher than 96" (2.4 m) above the floor. Remove any clogs from drain hose. | ||
HC (hot and cold hoses reversed) appears in display | Hot and cold inlet hoses have been installed incorrectly. | This code will appear at the end of the wash cycle to indicate that cold water hose is connected to the hot water inlet and hot water hose is connected to the cold water inlet. |
Sd (Excess suds) appears in display | Excessive suds in washer. Washer is running a suds reduction routine. | Allow the washer to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions. If the dial is flashing, reselect your desired cycle using a cold wash temperature, and press START/PAUSE. Do not add detergent. |
dL (Lid cannot lock) appears in display | An item in the load may be keeping the lid from locking. | Check for items directly under the lid. |
lid (Lid opened) appears in display | Washer lid left open. | Close the lid to clear the display. If the lid is left open for more than 10 minutes, the cycle will reset and water in the washer will drain. |
dU (Lid cannot unlock) appears in display | Objects on washer lid prevent it from unlocking. | Remove objects, such as a basket of laundry, from the top of the washer. |
F## code (F-type error code) appears in display | System error code. | Press START/PAUSE once to clear the code. Then press START/PAUSE again to restart washer. If code appears again, call for service. |
Whirlpool Aquasteam 9559 Washer Error Codes
Red indication lights up | Indication on big display (if available on your model) | Description Causes Solutions |
---|---|---|
“Water tap closed” | Appliance has no or insufficient water supply. The “Start/Pause” light blinks. Check whether: • Water tap is fully open and water supply pressure is sufficient. • Kinks are present in the water inlet hose. • Mesh filter of water supply hose is blocked • The water hose is frozen up. • The safety valve inspection window of your water supply hose is red (provided your appliance has a water supply hose as shown on picture “B”; replace the hose by a new one available through our After-Sales Service or your specialist dealer. After problem has been removed, restart programme by pressing “Start/Pause”. If the fault occurs again, contact our After-Sales Service. | |
“Clean pump” | Waste water is not pumped out. The appliance stops in the corresponding programme step; unplug it and check whether: • Kinks are present in the drain hose, or the hose is blocked for another reason. • Filter or pump is blocked. • The drain hose is frozen up. After problem has been removed, push the “Reset” button for at least 3 seconds; afterwards restart the desired programme. If the fault occurs again, contact our After-Sales-Service. | |
Aquasteam 9559 | ||
“Service” | from “F02” to “F35” (except “F24”) | “Electrical module fault” Push the “Reset” button for at least 3 seconds. |
from “F40” to “F43” | “Electrical module fault” Make sure that the water tap is open. If yes: • Switch the washing machine off by turning the programme selector to the “Off/O” position; then turn the programme selector to a wash programme again. If there is still a failure: • Push the “Reset” button for at least 3 seconds | |
“F24” | “Water level too high” (after programme cancellation or false operating). Switch off the washing machine by turning the programme selector to the “Off/O” position. Turn the programme selector to a wash programme again, shortly press the “Reset/Drain” button and press “Start /Pause” within 15 seconds to start the Drain programme. | |
“F02” or “FA” | “Waterstop fault” Turn the programme selector to the “Off/O” position, pull out the mains plug and turn the water tap off. Tilt the appliance forward carefully to allow collected water to flow out from the bottom. Then: • Plug in the appliance again. • Turn the water tap on (if water immediately flows into the appliance without the appliance being started, there is a failure; turn off the tap and notify the After-Sales Service). • Select and start the desired programme again. | |
“Fod” | “Overfoaming” Too much foam interrupted the wash programme. • Select and start the “Rinse & Spin” programme. • Afterwards select and start the desired programme again, using less detergent. If any of the faults described above persist, unplug the appliance, turn off the water tap and contact our After-Sales Service. | |
AWE 2217, AWE 6416, AWE 6517, AWE 6760, AWE 7516, AWE 8727, AWE 9527, AWE 9725 | ||
“Service” | “bdd” (in case your washing machine has no display: all lamps of the programme sequence indicator light up) | Appliance stops during the programme. “Drum flaps open” (the drum flaps have not been closed properly). Push the “Reset” button |
from “F02” to “F35” (except “F09”) | “Electrical module fault” Select and start “Drain” programme or push “Reset” button | |
“F09” | “Water level too high” (after programme cancellation or false operating). Switch off appliance and then switch it on again, select programme “Drain” and start within 15 sec. | |
“FA” | “Waterstop fault” Switch off appliance, pull out mains plug and turn water tap off. Tilt appliance forward carefully to allow collected water to flow out from the bottom. Then: • Plug in the appliance again. • Turn the water tap on (if water immediately flows into the appliance without the appliance being started, there is a failure; turn off the tap and notify After-Sales Service). • Select and start the desired programme again. | |
“Fod” | “Overfoaming” Too much foam interrupted the wash programme. • Select and start “Rinse & Spin” programme • Afterwards select and start desired programme again, using less detergent. If faults persist, unplug the appliance, turn off the water tap and contact our After-Sales Service. | |
AWO/C 0714 | ||
“Service” | from “F03” to “F43” (except “F18” and “F24”) | “Electrical module fault” Push the “Reset” button for at least 3 seconds. |
“F24” | May appear for very water-soaking laundry, or if you added too much laundry for a programme destined for small loads only. Do not overload the washing machine. Push the “Reset” button for at least 3 seconds to stop the programme. Select and start “Rinse and Spin” programme to complete the interrupted wash programme properly. | |
“F02” or “FA” | “Waterstop fault” For models with big display, the red “Waterstop” symbol Turn the programme selector to the “Off/O” position, pull out the mains plug and turn the water tap off. Tilt the appliance forward carefully (a second person must help you) to allow collected water to flow out from the bottom. Then: • Plug in the appliance again. • Turn the water tap on (if water immediately flows into the appliance without the appliance being started, there is a failure; turn off the tap and notify the After-Sales Service). • Select and start the desired programme again. | |
“F18” or “Fod” | “Overfoaming” Too much foam interrupted the wash programme. If your washing machine has a “Dosing Aid” function, and you used it: check if the dosing values set for the different programme groups correspond to the dosing values recommended for the detergents you use. • Select and start the “Rinse & Spin” programme. • Afterwards select and start the desired programme again, using less detergent. |
Whirlpool AWM 6100 Washer Error Codes
Small lamp lights up | Digital display | Fault description |
---|---|---|
“Water tap” | “FH” | “Water inlet fault” |
̶ | “FP” | “Draining fault” |
̶ | from “F4” to “F15” | “Electrical components fault” |
“Water Stop” | “FA” | “Water Stop fault” |
Water inlet fault (no or insufficient water supply) | For models with a fault display, the “Water tap” indicator is on or the display alternately shows “FH”. Switch off the appliance by turning the programme selector to the “O” position and unplug it. For models with no fault display, the washing machine stops in the appropriate step. Switch off the appliance and unplug it. Check whether: • the water tap is completely open, and the water supply pressure is sufficient; • the water inlet hose is kinked; • the mesh filters are blocked; • the water inlet hose is frozen. Reconnect the appliance to the electrical supply. For models with a fault display, reselect the desired programme and press the “Start/Pause” button again to continue with the programme (do not add detergent for this programme). For models without a fault display continue the programme by pressing the “On/Off” button again (do not add detergent for this programme). If the fault re-occurs, contact After-Sales Service. | |
Draining out fault | For models with a fault display, depending on the model, the display shows statically or alternately “FP”. Switch off the appliance by turning the programme selector to the “O” position and unplug it. For models with no fault display, the washing machine stops in the appropriate step. Switch off the appliance and unplug it. Check whether: • the drain hose is kinked; • the pump / filter are blocked; IMPORTANT: before draining, allow the wash water to cool down. • the drain hose is frozen. Connect the appliance to the electrical supply. For models with a fault display reselect the desired programme and press the “Start/Pause” button again to continue with the programme (do not add detergent for this programme). For models without a fault display continue the programme by pressing the “On/Off” button again (do not add detergent for this programme). If the fault re-occurs, contact After-Sales Service. | |
Electrical module fault | For models with a fault display “F4” to “F15” are displayed and some or all Spin Speed Selection LEDs are flashing. Switch off the appliance. Select a programme and press the “Start/Pause” button once again. The programme will continue. For models without a fault display the washing machine stops in the appropriate step. Switch the appliance first off, then on. The programme will continue. If the fault re-occurs, contact After Sales Service. | |
Water Stop fault (if available) | The “Water Stop” may have been triggered by: 1.too much foam. 2.a leak in the inlet hose or in the appliance. In this case the pump is switched on automatically in order to pump the water out. For models with a fault display the light of the “Water Stop” indication is on. The display shows “FA” or alternately “F” and “A” and the pump is running. Switch off the appliance by turning the programme selector to the “ ” position, unplug the appliance and make sure that the water tap is closed. For models without a fault display the washing machine stops in the appropriate step. Switch off the appliance, , unplug the appliance and make sure that the water tap is closed. Tilt the appliance forwards carefully to allow the collected water to flow out. Then: 1.plug in the appliance, 2.turn the water tap on (if water immediately flows into the appliance again, without the appliance being started, close water supply and call After-Sales Service). For models with a fault display reselect the desired programme and press the “Start/Pause” button again to continue with the programme (do not add detergent for this programme). For models without a fault display continue the programme by pressing the “On/Off” button again (do not add detergent for this programme). If the fault re-occurs, contact After-Sales Service |
Whirlpool WFC7500VW0 Washer Error Codes
DISPLAY AFFICHAGE | EXPLANATION | RECOMMENDED PROCEDURE |
---|---|---|
A09 | No water detected entering machine or pressure switch trip not detected | Water level is not reached within a defined time in normal wash cycle. Possible Causes/Procedure If there is no water in the unit: - Make sure that both valves at the water sou rce(s) are turned on all the way. - Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. - Verify inlet valve operation. - If there is water in the unit: - Verify drain pump operation. - Remove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub. - Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. Verify there is not a siphon problem. 2. Unplug washer or disconnect power. 3. Verifywire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 4. Check all hoses for possible leaks. 5. Plug in washer or reconnect power 6. Verify pressure switch operation. 7. Verify CCU operation by running a Quick Diagnostic Test or any cycle |
A10 | Long drain | If the drain time exceeds 4 minutes the water valves turn off. NOTES: Rotate knob to clear the display. Possible Causes/Procedure 1. Check the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power. 3. Remove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub. 4. Check the electrical connections at the pump and make sure the pump is running. 5. Check the drain pump filter for foreign objects. 6. Plug in washer or reconnect power. 7. If the above does not correct the problem, go to step 8. 8. Unplug washer or disconnect power. 9. Replace the pump. |
F01 | No water detected entering machine or pressure switch trip not detected | Water level is not reached within a variable time (EEPROM parameter) in whirlpool factory test Possible Causes/Procedure - If there is no water in the unit: - Make sure that both valves at the water source(s) are turned on all the way. - Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. - Verify inlet valve operation. If there is water in the unit: - Verify drain pump operation. - Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. - Remove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub 1. Verify there is not a siphon problem. 2. Unplug washer or disconnect power. 3. Verify wire harness connections to inlet valves, pressure swtch, drain pump and Central Control Unit (CCU). 4. Check all hoses for possible leaks. 5. Plug in washer or reconnect power 6. Verify pressure switch operation. 7. Verify CCU operation by running a Quick Diagnostic Test or any cycle |
F02 | Overflow condition | Overflow level has been reached, and last for more than 2 seconds. In an overflow condition, the door remains locked and the drain pump runs constantly, and after 10 minutes, door will be unlocked in order to cut off the valves power. Then if overflow s till happens, start pump again. Turn off hot and cold water faucets and unplug the unit before servicing. Possible Causes/Procedure 1. Check the drain hose and make sure it is not plugged or kinked. 2. Unplug washer or disconnect power, if water still flows into the washer, replace the water valve. 3. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Check/clean drain pump filter of foreign objects. 5. Check for drain pump failure. 6. Check the inlet valve for proper shut off. 7. Check the pressure switch for proper operation. 8. Rerrove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub. Debris in side the hose will not allow the switch to sense a pressure change. |
F03 | Long drain | If the drain time exceeds 4 minutes the water valves turn off .Only in factory test. NOTES: Rotate knob to clear the display. Possible Causes/Procedure 1. Turn washer ON to verify pump operates. 2. Check the drain hose and make sure it is not plugged or kinked. 3. Unplug washer or disconnect power. 4. Check the electrical connections at the pump and make sure the pump is running. 5. Check the drain pump filter for foreign objects. 6. Plug in washer or reconnect power. 7. If the above does not correct the problem, go to step 8. 8. Unplug washer or disconnect power. 9. Replace the pump. |
F05 | Water temperature sensor error | If the water temperature sensor (NTC) value is out of range (Below 23 degrees F. or above 217 degrees) during wash cycle. Possible Causes/Procedure 1. Unplug washer or disconnect power. 2. Check the water temperature sensor and connection to it 3. Check wire harness and connections between the Central Control Unit (CCU) and the water temperature sensor |
F06 | Drive motor tachometer error | If the control is unable to properly detect motor speed, the machine shuts down. Possible Causes/Procedure 1. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. Run Quick Diagnostics Test to check motor drive system. 3. Unplug washer or disconnect power. 4. Check wire harness connections between the drive motor and the motor control board, and between the Central Control Unit (CCU). 5. Plug in washer or reconnect power. |
F07 | Motor overspeed | If there the motor speed is not controlled then it will switch OFF the motor and wait for the speed decreased to Orpm. At the second occurrence in the same wash phase it will go to ERROR mode Possible Causes/Procedure 1. Run Quick Diagnostics Test to check motor drive system. 2. Unplug washer or disconnect power. 3. Check wire harness connections to the motor, and Central Control Unit (CCU)l 4. Check the drive system for any worn or failed components. 5. Plug in washer or reconnect power. 6. Check the CCU by looking for operations of the drive motor. 7. Check the drive motor for powered rotations. |
F13 | Door lock error | Failed attempts to lock the door within 10 seconds. This error code is only shown in whirlpool factory test. Possible Causes/Procedure - Door lock mechanism is broken or removed from door. - Door switchVlock unit failure. 1. Run Quick Diagnostics Test to check motor drive system. 2. Unplug washer or disconnect power. 3. Check door switch/lock unit. 4. Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). |
F14 | Eeprom error | A communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred. Possible Causes/Procedure - A power surge may cause this error. - Unplug washer or disconnect power for two minutes. - Verify CCU operation by running a Quick Diagnostic Test or any cycle. |
F21 | Serial communication error | The communication between the Central Control Unit (CCU) and the user interface board (Ul) cannot be sent correctly. Possible Causes/Procedure 1. Run Quick Diagnostics Test to check the User Interface boards and motor. 2. Unplug washer or disconnect power. 3. Check wire harness connections to the user interface and Central Control Unit (CCU). - Check connections of the CCU board within the housing. - Make sure all grounding switches are engaged. 4. Check that the serial harness at the Ul. 5. Plug in washer or reconnect power. |
F22 | Loads det ected during clean washer cycle | The load is detected in the drum during the start of clean washer cycle. Possible Causes/Procedure 1. Make sure that there is no load in the drum. If the drum is empty. 2. Rotate drum by hand to check for any binding of the spin basket. Possibility of clothing stuck between spin basket and outer tub or the rear seal may not be seated flush against rear bearings. 3. Check the drum's fixation. |
F23 | Pressure swtich error | The wash level and level heater safety are switched on at the same time Possible Causes/Procedure 1. Unplug washer or disconnect power. 2. Check wire harness connections to pressure switch and Central Control Unit (CCU). 3. Check connections of the CCU board within the housing. 4. Check the pressure switch for worn or failed conditions. |
F24 | Valves leakage/overflow failure | Overflow level has been reached for more than 5 times, but each period is shorter than 2 seconds. Possible Causes/Procedure 1. Check the drain hose and make sure it is not plugged or kinked. 2. Rerrove hose from pressure switch. Dislodge any debris build up in the hose inside the outer tub. 3. Unplug washer or disconnect power. 4. Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 5. Check/clean drain pump filter of foreign objects. 6. Check for drain pump failure. 7. Check the inlet valve for proper shut off. 8. Check the pressure switch for proper operation. |
F26 | Pump drive system error | When the connection between pump and the Central Control Unit (CCU) is lost during cycle drain Possible Causes/Procedure 1. Verify CCU operation by running a Quick Diagnostic Test or any cycle. 2. Unplug washer or disconnect power. 3. Check wire harness connections to the pump and Central Control Unit (CCU). 4. Plug in washer or reconnect power. |
F27 | Motor control unit error | Motor reversing error Possible Causes/Procedure 1. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. Perform Quick Diagnostic Test 3. Unplug washer or disconnect power. 4. Check wire harness connections between the drive motor, motor control board, and between the Central Control Unit (CCU). |
F28 | Motor control unit error | Motor High speed switch error Possible Causes/Procedure 1. Verify the shipping system including shipping bolts, spacers and cables are removed. 2. Perform motor Quick Diagnostic Test 3. Unplug washer or disconnect power. 4. Check wire harness connections between the drive motor, motor control board, and between the Central Control Unit (CCU). |
F29 | Door switch error | Door is not detected to be open and close for 3 continuous cycles. Possible Causes/Procedure 1. Power on the machine, and rotate knob to any cycle position, open the door and then close. Then press start button to continue to see if the error cleared. If the failure displaycondition still exists, go to step 2. 2. Run Quick Diagnostics Test to check door lock system. 3. Unplug washer or disconnect power. 4. Check the electrical connections at the side of door switch and the side of CCU, to make sure the connection is correct 5. Verify if the switch contacts are stuck closed. If closed and the door is open, replace the door switch mechanism. 6. Plug in washer or reconnect power. 7. If the above does not correct the problem, go to step 6 8. Unplug washer or disconnect power 9. Replace door switch 10. Replace CCU |
F30 | Door lock broken or door switch error | If it has been detected that door switch is open while the door is locked for more than 2 seconds. Door switch open while door is locked. 1. Push the door and check if it is completely closed. 2. Verify CCU operation by running a Quick Diagnostic Test or any cycle. 3. Verify if the switch contacts are stuck open. If open and the door are closed, replace the door switch mechanism |
Fod | Suds lock (overdose of detergent detected during the wash cycle) | If suds are detected continuously by the pressure switch during drain or spin, washer will enter Suds Detection mode. The washer will fill with 3/4 gallon (2.67 Liters) of water, then rest for 10 minutes with no tumbling. Washer will then drain. If error occurs during spin cycle, the unit will then start spinning. Possible Causes/Procedure - If too much detergent was used: - Run the unit through a RINSE/SPIN cycle. - Run a NORMAL cycle without adding any detergent. - This should clear the unit of the excess detergent. 1. Check the drain hose and make sure it is not plugged or kinked. 2. Is the drain standpipe higher than 9 feet, This can cause pump cavitations resulting in same failure code. 3. Unplug washer or disconnect power. 4. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 5. Check/clean drain pump filter of foreign objects. 6. Plug in washer or reconnect power. 7. Check drain pump. 8. Check the pressure switch and pressure switch hose. 9. Verify CCU operation by running a Quick Diagnostic Test or any cycle. |
Whirlpool LWA90AL Washer Error Codes
Error Message | Type of Error | Description |
---|---|---|
OP | Open Thermistor Error | Will be displayed at the end of a cycle. The first time “OP” or “SH” appears, the signal will sound for one minute, or until any pad is pressed. The washer will operate normally, but the regulated water temperatures will not be available (regulated cold and regulated hot). “OP” or “SH” will continue to appear when the control is in idle mode or when a cycle pad is pressed. |
SH | Shorted Thermistor Error | |
rP | Drain Error | Will be displayed when the washer is in a SPIN setting for four minutes and no water has been drained from the tub. The washer will operate normally. The error can be cleared by unplugging the washer. |
bP | Pressure Switch Error | Will be displayed when the washer senses a pressure switch error. The washer will not operate when this error is displayed. The error can be cleared by unplugging the washer. |
Whirlpool AWO5100 Washer Error Codes
CODES | CAUSES | SOLUTIONS |
---|---|---|
Err1 | Door is not properly shut. | Shut the door properly. |
Err2 | Drainage error, water not emptied within 4 minutes. | Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel. |
Err3 | Temperature sensor not properly connected or damaged. | Contact the maintenance personnel. |
Err4 | Heater error (Appears at the end of a cycle). | Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel. |
Err5 | Water level not met in 8 minutes. | Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. |
The height of the drain hose is below 80 cm. | Install drain hose within 80-100 cm of height. | |
The drain hose is in water. | Make sure the drain hose is not in water. | |
Err7 | Motor overheat protection or damage. | Contact the maintenance personnel. |
Err8 | Water exceeds protective level. | |
End | End of wash cycle. | |
1:25 | The remaining time is 1 hour 25 minutes. |
Whirlpool AWM05801 Washer Error Codes
FAILURE CODE | FAILURE INDICATOR | PROBABLE FAILURE | THE PROCESS TO BE DONE |
---|---|---|---|
E01 | The start/ pause light blinks. | The door is not shut properly. | Shut the door properly so that you hear the click. If the problem persists, turn off the machine unplug and apply to the nearest authorized service immediately. |
Err 02 | The program ready light blinks. | The water level in your machine is below heater. The pressure of your water sup- ply may be low or locking. | Turn on the tap to the end. Water may be cut, check it. lf the problem is still continuing, your machine will automatically stop after a while. Unplug your machine, turn off the tap and apply to the nearest authorized service. |
Err 03 | The start/ pause light and program ready light blinks . | The pump has failed or the pump filter is obstructed. | Clean the pump filter. If the problem persists, apply to the nearest authorized service. |
Err 04 | The program end light blinks . | Communication error | Shut down your machine and unplug. Turn off your tap and apply to the nearest authorized service. |
Whirlpool GVW9959KL0 Washer Error Codes
Error Codes | Meaning | Solution |
---|---|---|
PF flashes | Power Failure | Was the washing cycle interrupted by a power failure? Press START to continue the cycle from the moment that power was lost, - OR - Press STOP/CANCEL to clear the display and completely cancel the cycle. |
FL flashes | Over Fill | The washer will beep every 10 seconds with no time-out. The pump will cycle one half minute on, one half minute off, until the overfill switch is reset or power is discontinued to the unit. Press STOP/CANCEL to clear the display. Shut off the water faucets to the inlet hoses if water continues to flow. |
Er | Processor Reset Error | Cycle information was not stored during a power failure. Press STOP/CANCEL to clear the display. |
LF flashes | Long Fill | Are the water inlet hoses kinked or clogged? Are the water inlet valve screens clear? Press STOP/CANCEL to clear the display. |
CE flashes - beeps once | Communications Error | Press STOP/CANCEL to clear the display. |
Ld flashes | Long Drain | Is the drain hose kinked or clogged? Press STOP/CANCEL to clear the display. |
CA or CL | Current Limit | Is the washer overloaded? Press STOP/CANCEL to clear the display. |
Or | Open Relay | Washer operation failure. Call for service. |
Sr | Stuck Relay | |
LS flashes | Lid Switch Error | Is the washer lid open? Close the lid and press START to continue the cycle. Is the lid closed? Open and close the lid. Press STOP/ CANCEL to clear the display. |
SL | Suds Lock | Press STOP/CANCEL to clear the display. Extend Spin load; restart cycle. Do not add detergent. Use cold water. |
dt | Diagnostic Tests | For service diagnostics only. Press STOP/CANCEL to clear the display. |
ob | Off Balance | Is the load unbalanced? Redistribute the load. Close lid and press START. |
Whirlpool WTW6700T Washer Error Codes
Error Codes/Meaning | Solution |
---|---|
“LF” (Washer is taking too long to fill) | Check the following: Are the water inlet hoses kinked or clogged? Are the water inlet valve screens clear? Press PAUSE/CANCEL to clear display. Is the drain hose installed properly? |
“Ld” (Washer is taking too long to drain water from the wash tub) | Check the following: Is the drain hose kinked or clogged? Is the drain hose installed properly? Press PAUSE/CANCEL to clear display. |
“uL” (Unbalanced Load) | If the load is unbalanced, the washer will display this code while running an imbalanced load correction routine at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press START. |
“oL” (Over Load) | Is the washer overloaded? The washer has attempted to fill and begin the wash cycle. If the washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START. |
“Sd” (Suds Detected) | Did you use regular detergent? Regular or hand-washing detergents are not recommended for this washer. Use only High Efficiency (“HE”) detergent. |
“lid” (Lid Opened) | Is the lid open? Close the lid to clear the display. If the lid remains open for more than 10 minutes, water in the wash tub will drain. |
“HC” (Cold and Hot hoses switched) | This code will appear at the end of the wash cycle to indicate that the cold and hot water inlet hoses are switched. |
“dL” (Door/Lid cannot lock) | Indicates lid is not locked. Check for items caught in the lid keeping it from closing. Press PAUSE/CANCEL once to clear the code. |
“dU” (Door/Lid cannot unlock) | Is there excessive weight on the lid, such as a basket of laundry? Excessive weight will keep the lid from unlocking. Press PAUSE/CANCEL once to clear the code. |
“F##” code | Press PAUSE/CANCEL once to clear code. Press START. If code appears again, call for service. |
Whirlpool Duet Front-Loading Washer Error Codes
DISPLAY | EXPLANATION AND RECOMMENDED PROCEDURE |
---|---|
F/H | No water detected entering machine or Pressure switch trip not detected. If after 30 seconds the control does not detect water entering the machine and then valves will be turned off and the error code will be displayed. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it but has not detected the pressure switch trip, the valves will be turned off and the error code will flash. Press PAUSE/CANCEL twice to clear the display. Potential Causes - If there is no water in the unit: • Make sure that both valves at the water source(s) are turned on all the way. • Check for plugged or kinked inlet hoses or plugged screens in the inlet valves • Verify inlet valve operation - If there is water in the unit: • Verify Drain pump operation • Pressure Switch Hose is in good condition and properly connected to Tub and - Pressure switch - Verify there is not a siphon problem - Verify wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump, - Flow Meter, and Central Control Unit (CCU) - Check all hoses for possible leaks - Verify pressure switch operation - Verify flow meter operation - Verify CCU operation |
F/02 | Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and “F/02” is flashed. Press PAUSE/CANCEL twice to clear the display. NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F/02 error code will be displayed. Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check the electrical connections at the pump and make sure the pump is running. • Check the drain pump filter for foreign objects • If the above does not correct the problem replace the pump |
F/05 | Water Temperature Sensor Error If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the “F/05” error code will be displayed. Potential Causes • Check the Water Temperature Sensor, Heating Element, and Element Relay • Check connections to the Sensor, Heating Element and Relay |
F/06 | Drive Motor Tachometer Error The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. Potential Causes • Check wire harness connections between the Drive Motor/Tachometer and the Motor ControlUnit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the Drive Motor • Check the MCU • Check the Wire Harness |
F/07 | Motor Control Unit Error The Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU • Check the Drive Motor • Check the Wire Harness |
F/09 | Overflow Condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service. Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) • Check/ Clean Drain Pump Filter of foreign objects • Check for Drain Pump Failure • Check the Inlet Valve for proper shut-off • Check the Pressure switch for proper operation |
F/10 | Motor Control Unit (MCU) Heat Sink Thermal Trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and a “F/10” will be displayed. Potential Causes • Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU Check Motor |
F/11 | Serial Communication Error Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU • Check CCU • Check Motor • Check Wire Harness |
F/13 | Dispenser Circuit Error If the dispenser motor is not able to be driven to its proper position. Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check Dispenser Motor |
F/14 | EEPROM Error The Central Control Unit (CCU) receives its data from an EEPROM onboard the CCU. If there is an error reading this data it will cause this error. Potential Causes • A power glitch may cause this error. Try unplugging the Unit for two minutes to see if that fixes the error. • Check CCU. |
F/15 | Motor Control Unit (MCU) Error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU Check Motor • Check Wire Harness |
Sud | SUDS LOCK (Overdose of Detergent detected during the Wash Cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. If “Sud" is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Potential Causes • If too much detergent was used, run the unit through a Rinse/ Spin cycle then a Normal cycle without adding any detergent. This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) • Check/ Clean Drain Pump Filter of foreign objects • Check Drain Pump • Check the Pressure Switch • Check CCU |
F/dL | Door Lock Error A Door Lock Error occurs if the door cannot be locked. It will try to lock it 6 times before displaying the error. Potential Causes • Door Lock Mechanism broken or removed from the Door • Check Door Lock/Switch Assembly • Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) • Door Lock/Switch Assembly Failure |
F/dU | Door Unlock Error A Door Unlock Error occurs if the door cannot be unlocked. It will try to unlock the door 6 times before displaying the error. Potential Causes • Door Lock Mechanism broken. • Check Door Lock/Switch Assembly for foreign objects • Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) • Door Lock/Switch Assembly Failure Note: The Door Lock/Switch Assembly can be manually unlocked. |
Whirlpool Cabrio WTW6400S Washer Error Codes
DISPLAY (Saved Code) | EXPLANATION AND RECOMMENDED PROCEDURE |
---|---|
Long Fill | |
(F30) | LF flashes when the water level does not change for a period of time after the valves are turned on OR water has disengaged the basket but control does not detect a water level change. • Is water supply connected and turned on? • Are hose screens plugged? • Is water entering the tub? If so check pressure hose connection to machine/motor control. |
Long Drain | |
(F32) | Ld flashes when the water level does not change after the drain pump is on. • Is the drain hose or the drain pump dogged? • Is the drain hose height greater than 96" ? • Is the pump running? |
Unbalanced Load | |
(none) | uL is displayed when the machine/motor control detects an off-balance load, and is steady on while the washer runs a mini-cycle to rebalance the load. • Display clears if mini-cycle successfully rebalanced the load. • If the mini-cycle is unsuccessful. uL will flash until the door lid is opened, allowing the customer to view and redistribute the load. |
Overloaded | |
(F70) | oL flashes when the machine/motor control deteds a load size that exceeds the washer's capadty. • Open the door lid to clear display, remove excess laundry, then restart the cycle. |
Suds Detection | |
(F71) | Sd is displayed when the machine/motor control, by analyzing drag on the basket, detects a suds-lock condition, and is steady on while the control then runs a mini-clean out cycle. If the clean out cycle is unable to corred the over-sudsing problem, the cycle ends and Sd flashes in the display. This may signify: • Excessive detergent usage. • Basket cannot engage during drain step. • Mechanical friction on drive mechanism, not allowing basket to engage. |
Open/Close Door Lid | |
(F81) | Lid flashes when the following conditions occur: • User presses START with lid open. • User presses START after 2 consecutive machine cycles without opening lid. • The machine/motor control cannot detect the lid switch opening and dosing properly. |
Pump Out (lid opened) | |
(none) | Po flashes when drain pump begins pumping out water from tub upon activation by the door lid having been left open for more than 10 minutes. • Close door lid to stop drain pump. |
Hot, Cold Reversed | |
(none) | HC flashes when the hot and cold inlet hoses are reversed. • Make sure inlet hoses are connected correctly. |
Door Lock Failure | |
(F80, 82. 84.85) | dL flashes if the following conditions occur • Door lid is not closed completely due to interference. • Wash media buildup is preventing the lock bolt from extending. • Machine/motor control deteds open door lid switch when attempting to lock. • Machine/motor control cannot determine if door lid is in a locked state. |
Door Unlock Failure | |
(F83) | dU flashes if the following conditions occur: • Excessive force on door lid is preventing lock bolt from retracting. • Wash media buildup is preventing lock bolt from retrading. • Machine/motor control cannot determine if door lid is in an unlocked state. |
Primary Control Failure | |
(F60-68) | F then 1 flashes when there is a primary control failure. Replace the machine control assembly. |
Keypad/User Interface Failure | |
(F2) | F then 2 flashes when in: • Diagnostics Test mode if a stuck key is detected. • Standby mode if there is a user interface mismatch. |
ATC Thermistor Open/Short | |
(F40) | F then 40 flashes when the ATC Thermistor is detected to be open or shorted. |
Motor RPS Thermistor Open/Short | |
(F41) | F then 41 flashes when the motor rotor position sensor (RPS) thermistor is detected to be open or shorted. NOTE: This error code is only displayed when viewing saved fault codes. |
Heater Thermistor Open/Short (Not Used) | |
(F42) | F then 42 flashes when the heater thermistor is open or shorted. |
Motor Stalled | |
(F50) | F then 50 flashes when the motor rotor position sensor (RPS) senses no rotation. • Does basket turn freely? If not, make sure bottom shipping pack has been removed. Remove basket and look for foreign object. Determine cause of friction. • If basket turns freely |
Motor RPS Failure | |
(F51) | F then 51 flashes when there is a motor rotor position sensor (RPS) failure. |
Motor Stop Failure | |
(F52) | F then 52 flashes when the motor rotor position sensor (RPS) senses rotation after stop command. |
Motor Control Overtemp | |
(F53) | F then 53 flashes when the machine/motor control detects high temperature for the motor module. • Does basket turn freely? If not, determine cause of friction. • If basket turns freely |
Motor Control Overcurrent | |
(F54) | F then 54 flashes when the machine/motor control detects high current for the motor module. • Does basket turn freely? If not, determine cause of friction. • If basket turns freely |
Basket Re-engagement Failure | |
(F72) | F then 72 flashes when the basket check routine fails to determine if the basket is re-engaged after being disengaged. • Is the basket floating? If yes, pump out water. • Does basket turn freely? If not, determine cause of friction. |
Whirlpool Duet Steam Washer Error Codes
Codes/Cause | Solutions |
---|---|
“PF” (power failure) | Was the drying cycle interrupted by a power failure? Press and hold START to restart the dryer. |
“E” Variable (E1, E2, E3) | Call for service. |
“L2” Diagnostic Code. The drum will turn, but there may be a problem with your home power supply keeping the dryer's heater from turning on. | Check the following: Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit breaker. Select a Timed Dry heated cycle, and restart the dryer. If the message persists, consult a qualified electrician. The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display. The Estimated Time Remaining will return on the display. |
“AF” Diagnostic Code. The dryer vent may be crushed or blocked. | Check the following: Check to see if the vent run from the dryer to the wall is crushed. Confirm the vent run from the dryer to the wall is free of lint and debris. Confirm the exterior vent exhaust hood is free of lint and debris. Confirm your vent system falls within the recommended run length and number of elbows for the type of vent you are using. Select a Timed Dry heated cycle, and restart the dryer. If the message persists, have your entire home venting run cleaned. The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display. The Estimated Time Remaining will return on the display. |