Amana Washer Error Codes

The history of the Amana brand dates back to 1934. It was named after the place it was founded in (Middle Amana, Iowa). Today, it manufactures an array of household appliances, including products for the kitchen, laundry, and heating.
The lists of Amana error codes below will help you understand any problems you may be having with your washer. To start with, find the error code the washing machine is displaying. Now, find the list of error codes matching the model of the washer you use. Try the solutions suggested for your problems, starting from the easiest ones.
Amana Washer Error Codes

Amana TANDEM W10410362A washer error codes

If you experiencePossible CausesSolution
“Sd” (Excess suds) appears in displayExcessive suds in washer. Washer is running a suds reduction routine.Allow the washer to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions.
F8 followed by E1 (water supply error) appears in displayCheck for proper water supply.Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Touch POWER once to clear the code. Then touch POWER again to restart washer. If code appears again, call for service.
F9 followed by E1 (drain pump system error) appears in displayCheck plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 416" (114 mm).Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.
Not using HE detergent or using too much HE detergent.Use only HE detergent. Always measure detergent and follow manufacturer’s directions based on load size and soil level.
F5 followed by E2 (door will not lock) appears in displayWasher door not locking.Touch POWER to cancel the cycle. Make sure the door is closed completely and latching. Check for items in the washer drum that may be keeping the door from closing completely.
F7 followed by E1 (motor drive error) appears in displayMotor is having difficulty turning the drum.Washer is tightly packed. Remove some items.
“rL” (remove load) appears in displayLoad detected in drum during Clean Washer with affresh® cycle.Remove items from washer drum and restart Clean Washer with affresh® cycle.
Washer making error beepsDoor has not been opened and closed for at least 3 cycles.This code may appear when the washer is first turned on. Open and close the door to clear the display.
Washer beeps when HOLD TO START is touchedDoor not closed.Close the door completely.
F# E# code other than as described above appears in displaySystem error code.Touch POWER once to clear the code. Then touch POWER again to restart washer. If code appears again, call for service.
“nt” (interrupted) appears in displayThe cycle was paused or cancelled.The washer can take 20 to 30 minutes to stop spinning and drain and will display this error code during that time. Touch POWER once to clear the code. Then touch POWER again to restart washer.
Clean Washer LED flashing at end of wash cycleThe washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer cycle.Run the Clean Washer cycle. If the Clean Washer cycle is not turned on, the LED will stop flashing at the end of a wash cycle after running 3 more regular wash cycles. After 30 more wash cycles are completed, the Clean Washer LED will again flash at the end of a wash cycle as a reminder.

Amana NFW7200TW washer error codes

LED DisplayDescriptionDiagnostic code
ndThe water level fails to drop below the Low Water level reset within 15 minutes, before a spin begins.1
LODoor failed to unlock after 3 attempts.2
nFContinuous fill of 12 minutes. Total fill of 14 minutes.3
FLDoor failed to lock after 3 attempts.4
LEWater sensor level fault.8
OEA fault is detected in the water level sensor. Data (frequency) shows the water level is at or above the overflow level.E
E2A key is sensed to be pressed more than 30 seconds, the key will be assumed to be stuck.15
dcNever exceeded 400 rpm due to an unbalanced load.10
odThe door has not been opened after two complete wash cycles. Door switch was not seen open since the last two final spins.17
dLOpen door lock switch with motor running.18
dSDoor switch is read as open and the door locked switch is read as locked.22
bEMotor tach signal exists without motor running.25
tEAbnormal high/low temp or ohm resistance seen.29
E3Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving. (Locked, Hall Sensor fault)2E


Diagnostic Codes
Diag. CodeDescriptionTriggerAction to be taken
1No DrainThe water level fails to drop below the Low Water level reset within 15 minutes, before a spin begins.Displays "nd"
2The door/lid fails to unlockDoor failed to unlock after 3 attemptsDisplays "LO"
3No FillContinuous fill of 12 minutes. Total fill of 14 minutes.Displays "nP"
4The door/lid fails to lockDoor failed to lock after 3 attemptsDisplays "FL”
5-7Not Used
8Water level sensor fault.Input signal from water level Sensor is out of range, Washer will beep and pause the wash cycle.Displays "LE"
9Not Used
10Unbalance or cabinet hit detected during final spin, which prevented the spinner from exceeding 400 rpmNever exceeded 400 rpm due to an unbalanced load.Will display "dc"
EWater sensor level fault.Water level in the machine is believed to be above the overflow level. When this condition is detected, the machine will automatically begin pumping water out of the machine until it falls below the overflow level.First check to see that water valve is not stuck. If water valve is OK, check water level sensor
11Will not remember machine settingsDifficulty in reading memoryGo to "Clear diagnostic codes". Disconnect and reconnect the washer power cord at power supply outlet. If condition still exists, replace machine control board.
12-14Not Used
15Stuck KeyA key is sensed to be pressed more than 30 seconds, the key will be assumed to be stuckDisplay "E2". Go to "Membrane Pad Check". Check connection of keypad to control board. Replace console if necessary.
17Door/Lid switch was not seen open since the last three final spinsThe door has not been opened after two complete wash cycles. Door switch was not seen open since the last two final spinsWill display "od" If door open sensing, will cleared.
18Detected door lock switch open during cycle when not expected.Open door lock switch with motor running.Check for loose wire connections Clear the diagnostic code and recheck; if reoccurs, perform Diagnostic Motor/Machine Control Board test Check for faulty motor relay on the machine control board.
19-21Not Used
22Door/lid switch seen open during cycle (when not paused).Door switch is read as open and the door locked switch is read as locked.
23-24Not Used
25Motor tach signal exists without motor running.Tach signal exists without torque commanded or when not expected (Abnormal condition only).Displays " bE". Replace motor control board.
26-28Not Used
29Sump Thermistor failure (Optional)Abnormal high/low temp or ohm resistance seenDisplays" tE".
- Loose or pinched wires
- Bad sump thermistor
2EMotor Drive failure (Locked, Hall sensor fault)Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving.Display “E3" Evaluate wire harness for loose or unhooked connections. If machine has separate motor control, perform self diagnostic motor test.
30-33Not Used
34System Relay failureMachine control does not see relay open when it should.Display "Sr". Replace machine control board.
35Not Used
36Heater relay failure.Heater Relay Check signal not sensed.Display "Hr". Replace machine control board.
3EMotor failure (Over current)Over Current is detected. Motor won't turn.Displays "3E". Check the motor windings, the speed sensor, wiring connections, or Control Board.
40-90Not Used
91Voltage for motor control bus is over specified limitVoltage for motor control bus is over specified limitDisplay "2E". Replace motor control board.
92Voltage for motor control bus is under specified limitVoltage for motor control bus is under specified limit

Amana NTC3500FW washer error codes

If you experiencePossible CausesSolution
E1 - Water inlet alarmWater level not reached after 20 minutes.Check that the water faucets are not closed.
Check that the water pressure in the house is over 20kPa.
Clean the inlet hose filter screens.
Check that the drain hose is not below 271/2" (700 mm) from the floor.
E2 - Draining alarmWasher is still detecting water after draining for 8 minutes.Check that the drain hose is not more than 39/3" (100 cm) from the floor.
Remove any clogs from the drain hose.
E3 - Unbalanced alarmWasher may be tightly packed or clothes are not evenly distributed.Remove several items, rearrange load evenly around the washplate, and restart the Spin cycle.
E4 - Open lid alarmOpening the lid during the Spin cycle.Close the lid.
EA or EC - Other errorsOtherCall for technical assistance

Amana W10211354C washer error codes

CodePosible/Cause
“F20” (Water Inlet Problem—no water or insufficient water supply)Select STOP twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
Are both hot and cold water faucets completely turned on? Are screens at inlet hose connection to washer clogged?
Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug in washer or reconnect power. Re-select cycle and press START. If the problem remains, call for service.
“F21” (Drain Problem)Select STOP twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96" (2.4 m) above the floor?
Plug in washer or reconnect power. Re-select cycle and press START. If the problem remains, call for service.
“SUD” (Suds Routine)When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. “SUD” is displayed during rinsing and at the end of the cycle to inform you that Suds Routine was activated. Use only HE (High Efficiency) detergents.
“F22” (Front door lock)Select STOP twice to cancel the cycle.
Check the following:
Is the washer door firmly shut?
The door must be completely closed for the washer to operate. The door may look closed, but may not be latched. Open the door and close firmly.
Were you washing a large load?
Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to tumble freely. An overloaded basket may keep the door from shutting completely. Reduce your load size if needed.
Press POWER and select START.
“F” codes other than F20, F21 or F22Select STOP twice to cancel the cycle. Select RINSE/DRAIN & SPIN if there is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call for service.