Samsung Washer Error Codes

Samsung washers are widely known around the globe and have a huge demand on world`s market. The production is released by South Korean Samsung Electronics company, belonged to the industrial Samsung Group. The last one is considered to be the greatest manufacturer of household, audio, video and telecommunications equipment, etc. These days Samsung Electronics has representative offices and production facilities in 60 countries around the world. More than 425 thousand of specialists work hard on designing and creating the production with the help of the latest achievements of science and technology.

Nowadays Samsung washers allow to completely automate the hard physical labor caused by daily washing. It performs a full cycle of work – soaking, boiling, rinsing, conditioning, spinning and so on. The unexpected breakage of household appliances amounts to a real catastrophe.

But almost all Samsung models are equipped with a system for monitoring and determining the problem. The result is displayed on the washer`s screen in a form of the certain code. For successful work with them, you need the error codes of Samsung washers, listed in the table below. It is easy and intuitively clear to use. There you can find codes for all contemporary Samsung models. In most cases, you can fix the technique by yourself even without having any experience and knowledge. In exceptional cases, it will be better to contact the repair service.

Samsung WA48J7700A, WA48J7770A Top Load Washer with active wash error codes

The washer may display information codes to help you understand what is occurring with your washer better.

CodeAction
1CThe Water Level sensor is not working properly.
• Check WaterLevel Sensor wire harness.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “1C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
3CCheck the motor for operation.
• Try restarting the cycle.
• If the problem continues, call for service.
4CWater is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufficient water pressure.
• Make sure that the cold water tap and the hot water tap are properly connected.
• Clean the mesh filter as it may be clogged.
NOTE
When the washer displays “4C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
4C2• Make sure the cold water supply hose is firmly connected to the cold water tap.
If it is connected to the hot water tap, the laundry may be deformed with some cycles.
5CWater is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending on the connection type.
• Clean the debris filter as it may be clogged.
• Make sure the drain hose is straightened all the way to the drain system.
• If the information code remains, contact a customer service centre.
9C1The electronic control needs to be checked (Over Voltage Check).
• Check the PCB and wire harness.
• Check if power is supplied properly.
• If the information code remains, contact a customer service centre.
9C2Low voltage detected
• Check if the power cord is plugged in.
• If the information code remains, contact a customer service centre
AC6Inverter Communication problem
• Check the Inverter PCB and wire harness.
• If the information code remains, contact a customer service centre.
dCOperating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
HCHigh temperature heating check
• If the information code remains, contact a customer service centre.
LCCheck the drain hose.
• Make sure the end of the drain hose is placed on the floor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “LC”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
OCWater is overflowed.
• Restart after spinning.
• If the information code remains on the display, contact a local Samsung service centre
PCWhen position of the clutch can't be detected.
• If the information code remains, contact a customer service centre.
PC1After position of the clutch is detected, if the signal of the clutch hall goes wrong.
• If the information code remains, contact a customer service centre.
UbSpinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a flat, stable surface.
• Redistribute the load. If only one item of clothing needs washing, such as a bathrobe or pair of jeans, the final spin result might be unsatisfactory, and an “Ub” check message will be shown in the display.

Samsung WF42H5200A, WF42H5100A, WF42H5000A Front Load Washer with SuperSpeed error codes

ERROR CODEMEANING & SOLUTION
UEUnbalanced load prevented your washer from spinning. Redistribute the load, press the Start/Pause button.
dEThe door is open when the washer is running.
Close the door tightly and restart the cycle. If the code reappears, call customer service.
dE1Your washer failed to lock or unlock the door.
HEA water temperature control problem. (Heater control problem). Call customer service.
LEYour washer has tried to fill, but has not reached the proper water level. Call customer service.
When the washer displays the “LE” code, the washer drains for 3 minutes. During this time, the Power button is inoperative.
5EYour washer is not draining. This can also mean that the unit senses a small clog while draining.
1. Turn off the unit for 10 seconds and then turn it on again.
2. Select the Spin Only cycle.
3. Press the Start/Pause to drain the water.
If it still does not drain, call for service.
4EYour washer has tried to fill but was unsuccessful.
Make sure the water faucets are open all the way. Check for bent hoses. Check the inlet screens on the hoses. If you are using a Flood Safety Device, please remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.
You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function if the temperature of the cold water is lower than 59°F.
When washer displays “4E”, washer do draining for 3 minutes. At this time, the Power button is invalid.
4E2The hot/cold water hose connection is not correct. Please connect the hot/cold water hose correctly.
OEA fault is detected in the water level sensor. Call customer service.
1EThe Water Level sensor is not working properly. Call customer service. When the washer displays the “1E” code, the washer drains for 3 minutes. During this time, the Power button is inoperative.
BE2A jammed key. Call customer service.
tE1A temperature sensor problem. Restart the cycle. If the code reappears, call customer service.
3EA motor problem. Restart the cycle. If the code reappears, call customer service.
9E1/9E2High/Low voltage detected. Restart the cycle. If the code reappears, call customer service.
AE8A Communication error between the MAIN PBA and the INVERTER PBA. Call customer service.
8EA MEMS sensor problem. Call customer service.
SF1
SF2
SF3
A system error. Call customer service.
SUdToo many suds are detected during the wash session. The unit is put on hold until the amount of suds have been reduced. When suds have been reduces, the washer will re-start.

Samsung WF56H9110C, WF42H5400A, WF42H5500A, WF42H5700A, WF42H5600A, WF45H6300A, WF45H6100A Front Load Washer with SuperSpeed error codes

ERROR CODEMEANING & SOLUTION
UEUnbalanced load prevented your washer from spinning. Redistribute the load, press the Start/Pause button.
dEThe door is open when the washer is running.
Close the door tightly and restart the cycle. If the code reappears, call customer service.
dE1Your washer failed to lock or unlock the door.
HEA water temperature control problem. (Heater control problem). Call customer service.
LEYour washer has tried to fill, but has not reached the proper water level. Call customer service.
When the washer displays the “LE” code, the washer drains for 3 minutes. During this time, the Power button is inoperative.
5EYour washer is not draining. This can also mean that the unit senses a small clog while draining.
1. Turn off the unit for 10 seconds and then turn it on again.
2. Select the Spin Only cycle.
3. Press the Start/Pause to drain the water.
If it still does not drain, call for service.
4EYour washer has tried to fill but was unsuccessful.
Make sure the water faucets are open all the way. Check for bent hoses. Check the inlet screens on the hoses. If you are using a Flood Safety Device, please remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.
You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function if the temperature of the cold water is lower than 59°F.
When washer displays “4E”, washer do draining for 3 minutes. At this time, the Power button is invalid.
4E2The hot/cold water hose connection is not correct. Please connect the hot/cold water hose correctly.
OEA fault is detected in the water level sensor. Call customer service.
1EThe Water Level sensor is not working properly. Call customer service. When the washer displays the “1E” code, the washer drains for 3 minutes. During this time, the Power button is inoperative.
BE2A jammed key. Call customer service.
tE1A temperature sensor problem. Restart the cycle. If the code reappears, call customer service.
3EA motor problem. Restart the cycle. If the code reappears, call customer service.
9E1/9E2High/Low voltage detected. Restart the cycle. If the code reappears, call customer service.
AEA Communication error between the SUB(Sensor) PBA and the MAIN PBA. Call customer service.
8EA MEMS sensor problem. Call customer service.
SF1
SF2
SF3
A system error. Call customer service.
SUdToo many suds are detected during the wash session. The unit is put on hold until the amount of suds have been reduced. When suds have been reduces, the washer will re-start.
AE6A Communication error between the MAIN PBA and the INVERTER PBA.

Samsung WA52J8060A, WA52J8700A Top Load Washer with active wash error codes

Information CodeMeaningAction
UBUnbalanced load prevents washer from spinning.Redistribute the load, and then press the Start/Pause button.
dC1The washer did not properly lock the door.Make sure the door is firmly closed. Restart the washer. If the code reappears, call customer service.
5CThe washer does not drain. The washer may detect a small clog while draining.1. Restart the washer.
2. Select the Spin Only cycle.
3. Press the Start/Pause button to drain the water.
If the washer still does not drain, call customer service.
4CYour Washer has tried to fill but was unsuccessful.
Check if the hot water supply hose is connected.
Check for the water taps and hoses connection(hose bent and inlet screens). If using a flood safety device, remove the device and directly connect the water hoses to the washer.
The hot water supply hose must be connected because the Auto Temperature Control (A.T.C.) function supplies hot water if the temperature of cold water is lower than 59 °F.
tC1Temperature sensor problemRestart the washer. If the code reappears, call customer service.
3CMotor problem.
dCLid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
dC1Your washer failed to lock the lid
LCWater level problem.Call customer service.
OC/1CWater level sensor problem
bC2Jammed button.
ACCommunication error (SUB (sensor) PBA - MAIN PBA).
AC3Communication error (DR Module - MAIN PBA).
AC4Communication error (WIFI PBA - MAIN PBA)
AC5Communication error (LCD PBA - MAIN PBA)
AC6Communication error (Inverter PBA - MAIN PBA)
8C/8C2MEMS sensor problem
4C2This occurs when the temperature exceeds 50, for over 8 seconds in the Wool and Delicates course.
PCWhen position of the clutch can’t be detected.
PC1After position of the clutch is detected, if the clutch position is wrong, occurs error
Sud/SdThe washer has detected too many suds. The washer will stop operating until the amount of suds has reduced. The washer will then resume normal operation.

Samsung WA45H7000A, WA48H7400A, WA45H7200A Top load washer error codes

Error codes washer. The Washer may display information codes to help you understand what is occurring with your Washer better.

CODE SYMBOLMEANINGSOLUTION
1EThe Water Level sensor is not working properly.
When washer displays “1E”, washer will drain for 3 minutes. At this time, the Power button is invalid
Call for service.
4EYour Washer has tried to fill but was unsuccessful. Check if the hot water supply hose is connected.
When washer displays “4E”, washer will drain for 3 minutes. At this time, the Power button is invalid.
Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, then please remove the device and connect the water hoses directly to the unit.
You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function.
5EYour washer is not draining. It can also mean that the unit senses a small clog while draining.Do the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water. If it still does not drain, call for service.
LEYour Washer has tried to fill but has not reached the proper water level.
When washer displays “LE”, washer will drain for 3 minutes. At this time, the Power button is invalid.
Call for service.
UEUnbalanced load prevented your Washer from spinning.Redistribute the load, press the Start/Pause button.
dELid is open when washer is runningClose the lid tightly and restart the cycle. If the code reappears, call for service.
dE1Your washer failed to lock or unlock the lid.Close the lid tightly and restart the cycle. If the code reappears, call for service.
dE1The door will not unlock.Make sure the lid is firmly closed.
Push the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
bE2A jammed KeyCall for service.
3EMotor not running properly.Restart the cycle pressing the Start/Pause button. If the code reappears, call for service.
AECommunication error between SUB PBA and MAIN PBA.Call for service.
8E
8E1
8E2
Mems sensor problem.Call for service.
tE1Temperature sensor problem.Restart the cycle.
If the code reappears, call for service.
OEA fault is detected in the water level sensor.Call for service.
4E2This occurs when the temperature exceeds 50 degrees for over 8 seconds in the Wool and Delicates cycle.Call for service.
AE6Commuication error between INVERTER PBA and MAIN PBA.Call for service.

Samsung SK-4A/XAA, WF218ANB, WF218ANW, WF219ANB, WF219ANW washer error codes

CODE SYMBOLMEANINGSOLUTION
dcUnbalanced load prevented your Washer from spinning.Redistribute the load, press the Start/Pause Button.
dLDoor is unlocked when Washer is running.Press the Power button to turn off your Washer, then restart the cycle. If the code reappears, call for service.
dSDoor is open when Washer is running.Close the door tightly and restart the cycle. If the code reappears, call for service.
FLYour Washer failed to lock the door.Close the door tightly and restart the cycle.
If the code reappears, call for service.
HrWater temperature control problem. (Heater Control problem)Call for service.
LEYour Washer has tried to fill but has not reached the proper water level.Call for service.
LOThe door will not unlock.Make sure the door is firmly closed.
Push the Power button to turn off your Washer, then turn it on again. If the code reappears, call for service.
E3Motor not running properly.Restart the cycle pressing the Start/Pause Button. If the code reappears, call for service.
ndYour washer is not draining.
It can also mean that the unit senses a small clog while draining.
Before calling for service, check the following.
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
Clean the debris filter. If it still does not drain, call for service.
nFYour Washer has tried to fill but was unsuccessful.Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses
nFIThe hot/cold water hose connection is not correct.Please connect the hot/cold water hose connection correctly
SrProblem with control.Call for service.
PFElectric service was lost when Washer was running.Restart the cycle by pressing the Start/Pause Button.
OEA fault is detected in the water level sensor.Call for service
bEJammed Key.Call for service
bEMotor speed sensor problem.Restart the cycle.
If the code reappears, call for service.
tETemperature sensor problem.Restart the cycle.
If the code reappears, call for service.
3EHigh current detected.Restart the cycle.
If the code reappears, call for service.
2EHigh/Low voltage detected.Restart the cycle.
If the code reappears, call for service.
SdToo many suds are detected during the washing session.
The unit is put on hold until the suds are reduced. Then, the unit will go back to the operation.
When it finishes washing, End and Sd codes will blink in turn.
To prevent it, cut down on detergents.

Samsung WA40J3000A series washer error codes

CODE SYMBOLMEANINGSOLUTION
Hot LED FlashesLid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
Warm LED FlashesCommunication error between SUB PBA and MAIN PBA.Call for service.
Cold LED FlashesA button is not working properly.Call for service.
Tap Cold LED FlashesThe Water Level sensor is not working properly.
!!! When the Tap Cold LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Call for service.
Extra Large LED FlashesYour Washer has tried to fill but was unsuccessful.
!!! When the Extra Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function.
Large LED FlashesYour Washer has tried to fill but has not reached the proper water level.
!!! When the Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Call for service.
Medium LED FlashesA fault is detected in the water level sensor.Call for service.
Small LED FlashesYour washer is not draining. It can also mean that the unit senses a small clog while draining.Do the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.
Hot & Warm LEDs flashUnbalanced load prevented your Washer from spinning.Redistribute the load, and then press the Start/ Pause button.
Hot & Cold LEDs flashMotor not running properly.Restart the cycle by presssing the Start/Pause button. If the code reappears, call for service.
Hot & Tap Cold LEDs flashMems sensor is not working properlyCall for service.
Hot & Extra Large LEDs flashDoor lock is not working properlyClose the lid tightly and restart the cycle. If the code reappears, call for service.
Hot & Large LEDs flashDoor lock is not working properly.Close the lid tightly and restart the cycle. If the code reappears, call for service.
Hot & Medium LEDs flashThermistor is not working properly.Call for service.
Hot & Small LEDs flashThe temperature of the supplied water is so high.Ensure that the cold water tap and the hot water tap are connected correctly. If the code reappears, call for service.

Samsung WF361, WF363, WF365, WF364 series washer error codes

CODE SYMBOLMEANINGSOLUTION
dcUnbalanced load prevented your washer from spinning.Redistribute the load, press the Start/Pause Button
dSDoor is open when washer is running.Close the door tightly and restart the cycle.
If the code reappears, call for service.
FLYour washer failed to lock the door.Close the door tightly and restart the cycle.
If the code reappears, call for service.
HrWater temperature control problem.
(Heater Control problem)
Call for service.
LEYour washer has tried to fill but has not reached the proper water level.Call for service.
LOThe door will not unlock.Make sure the door is firmly closed.
Push the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
3EMotor not running properly.Restart the cycle by pressing the Start/Pause Button. If the code reappears, call for service.
ndYour washer is not draining.
It can also mean that the unit senses a small clog while draining.
First, clean the drain filter. Then do the following.
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
Clean the debris filter.
If it still does not drain, call for service.
nFYour washer has tried to fill but was unsuccessful.Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, then please remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function if the temperature of the cold water is lower than 59 °F
nFIThe hot/cold water hose connection is not correct.Please connect the hot/cold water hose correctly
PFElectric service was lost when the washer was running.Restart the cycle by pressing the Start/Pause Button.
OEWater detected over the safe water level.Call for service
E2Jammed Key.Call for service
bEMotor speed sensor problem.Restart the cycle.
If the code reappears, call for service.
tETemperature sensor problem.Restart the cycle.
If the code reappears, call for service.
2EHigh/Low voltage detected.Restart the cycle.
If the code reappears, call for service.
SUDToo much suds is detected during the washing session.
The unit is put on hold until the suds are reduced. Then, the unit will resume operation.
When it finishes washing, the End and Sd codes will blink in turn.
To prevent, reduce the amount of detergent.

Samsung WF56H9100A, WA48H7400A, WA45H7200A, WA45H7000A series washer error codes

ERROR CODEMEANING & SOLUTION
UEUnbalanced load prevented your washer from spinning.
Redistribute the load, press the Start/Pause button.
dEThe door is open when the washer is running.
Close the door tightly and restart the cycle. If the code reappears, call customer service
dE1Your washer failed to lock or unlock the door.
The door will not unlock.
Make sure the lid is firmly closed.
Push the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
HEA water temperature control problem. (Heater control problem)
Call customer service.
LEYour washer has tried to fill, but has not reached the proper water level.
Call customer service.
!!! When the washer displays the “LE” code, the washer drains for 3 minutes. During this time, the Power button is inoperative.
5EYour washer is not draining. This can also mean that the unit senses a small clog while draining.
1. Turn off the unit for 10 seconds and then turn it on again.
2. Select the Spin Only cycle.
3. Press the Start/Pause to drain the water.
If it still does not drain, call for service.
4EYour washer has tried to fill but was unsuccessful.
Make sure the water faucets are open all the way. Check for bent hoses. Check the inlet screens on the hoses. If you are using a Flood Safety Device, please remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.
You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function if the temperature of the cold water is lower than 59°F.
!!! When washer displays “4E”, washer do draining for 3 minutes. At this time, the Power button is invalid.
4E2The hot/cold water hose connection is not correct.
Please connect the hot/cold water hose correctly.
OEA fault is detected in the water level sensor.
Call customer service.
1EThe Water Level sensor is not working properly.
Call customer service.
!!! When the washer displays the “1E” code, the washer drains for 3 minutes. During this time, the Power button is inoperative.
BE2A jammed key.
Call customer service.
tE1A temperature sensor problem.
Restart the cycle. If the code reappears, call customer service.
3EA motor problem.
Restart the cycle. If the code reappears, call customer service.
9E1/9E2High/Low voltage detected.
Restart the cycle. If the code reappears, call customer service.
AEA Communication error between the SUB(Sensor) PBA and the MAIN PBA
Call customer service.
8E
8E2
A MEMS sensor problem.
Call customer service.
SF1
SF2
SF3
A system error.
Call customer service.
SUdToo many suds are detected during the wash session. The unit is put on hold until the amount of suds have been reduced. When suds have been reduces, the washer will re-start.
AE8A Communication error between the MAIN PBA and the INVERTER PBA.
Call customer service.
PEWhen position of the clutch can’t be detected.
Call for service.
PE1After position of the clutch is detected, if the signal of the clutch hall goes wrong, an error occurs.
Call for service.
AE6Commuication error between INVERTER PBA and MAIN PBA.
Call for service.

Samsung WA48J7770AW/A2 washer error codes

Information CodeMeaningAction
UbUnbalanced load prevents washer from spinning.Redistribute the load, and then press the Start/Pause button.
dC1The washer did not properly lock the door.Make sure the door is firmly closed. Restart the washer. If the code reappears, call customer service
5CThe washer does not drain. The washer may detect a small clog while draining.1. Restart the washer.
2. Select the Spin Only cycle.
3. Press the Start/Pause button to drain the water.
If the washer still does not drain, call customer service
4CYour Washer has tried to fill but was unsuccessful. Check if the hot water supply hose is connected.Check for the water taps and hoses connection(hose bent and inlet screens). If using a flood safety device, remove the device and directly connect the water hoses to the washer.
The hot water supply hose must be connected because the Auto Temperature Control (A.T.C.) function supplies hot water if the temperature of cold water is lower than 59 °F.
tC1Temperature sensor problem.Restart the washer. If the code reappears, call customer service.
3CMotor problem.
dCLid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
dC1Your washer failed to lock the lid.
LCWater level problem.Call customer service.
OC/1CWater level sensor problem
bC2Jammed button.
ACCommunication error (SUB (sensor) PBA - MAIN PBA).
AC3Communication error (DR Module - MAIN PBA).
AC4Communication error (WIFI PBA - MAIN PBA)
AC5Communication error (LCD PBA - MAIN PBA)
AC6Communication error (Inverter PBA - MAIN PBA)
8C/8C2MEMS sensor problem
4C2This occurs when the temperature exceeds 50, for over 8 seconds in the Wool and Delicates course
PCWhen position of the clutch can’t be detected.
PC1After position of the clutch is detected, if the signal of the clutch hall goes wrong, occurs error.
Sud/SdThe washer has detected too many suds. The washer will stop operating until the amount of suds has reduced. The washer will then resume normal operation.

Samsung WA456, WA422, WA400 Top load washer error codes

The Washer may display information codes to help you understand what is occurring with your Washer better.

CODE SYMBOLMEANINGSOLUTION
IE code
The Water Level sensor is not working properlyCall for service.
nF code
Your Washer has tried to fill but was unsuccessful.Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, then please remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connectedYou must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function.
nd code
Your washer is not draining. It can also mean that the unit senses a small clog while draining.Do the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.
LE code
Your Washer has tried to fill but has not reached the proper water level.Call for service.
dc code
dc
Unbalanced load prevented your Washer from spinning.Redistribute the load, press the Start/Pause button.
dS code
dS
Lid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
FL code
FL
Your washer failed to lock the lid.Close the lid tightly and restart the cycle. If the code reappears, call for service.
LO code
LO
The door will not unlockMake sure the lid is firmly closed.
Push the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
E2 code
E2
Jammed Key.Call for service
3E code
3E
Motor not running properlyRestart the cycle pressing the Start/Pause button. If the code reappears, call for service.
AE code
Communication error between SUB PBA and MAIN PBACall for service.
8E code
8E1 code
8E2 code
Mems sensor problem.Call for service.
tE code
tE
Temperature sensor problem.Restart the cycle.
If the code reappears, call for service.
nF code
(WA422/WA400)

nF1 code
(WA456)
The hot/cold water hose connection is not correct.Please connect the hot/cold water hose connection correctly.
OE code
OE
A fault is detected in the water level sensor.Call for service
SUd code
Sd code
Suds is detected during the spinning session. (“SUd” or “Sd” is not an error.
When it finishes washing, End and the “SUd” or “Sd” code will blink in turn.)
Guide a user to reduce amount of detergent usage.

Samsung WA56H9000AP/A2 washer error codes

The Washer may display information codes to help you understand what is occurring with your Washer better.

CODE SYMBOLMEANINGSOLUTION
1EThe Water Level sensor is not working properly.
When washer displays “1E”, washer will drain for 3 minutes. At this time, the Power button is invalid
Call for service.
4EYour Washer has tried to fill but was unsuccessful. Check if the hot water supply hose is connected.
When washer displays “4E”, washer will drain for 3 minutes. At this time, the Power button is invalid.
Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, then please remove the device and connect the water hoses directly to the unit.
You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function.
5EYour washer is not draining. It can also mean that the unit senses a small clog while draining.Do the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water. If it still does not drain, call for service.
LEYour Washer has tried to fill but has not reached the proper water level.
When washer displays “LE”, washer will drain for 3 minutes. At this time, the Power button is invalid.
Call for service.
UEUnbalanced load prevented your Washer from spinning.Redistribute the load, press the Start/Pause button.
dELid is open when washer is runningClose the lid tightly and restart the cycle. If the code reappears, call for service.
dE1Your washer failed to lock or unlock the lid.Close the lid tightly and restart the cycle. If the code reappears, call for service.
dE1The door will not unlock.Make sure the lid is firmly closed.
Push the Power button to turn off your washer, then turn it on again. If the code reappears, call for service.
bE2A jammed KeyCall for service.
3EMotor not running properly.Restart the cycle pressing the Start/Pause button. If the code reappears, call for service.
AECommunication error between SUB PBA and MAIN PBA.Call for service.
8E
8E2
Mems sensor problem.Call for service.
tE1Temperature sensor problem.Restart the cycle.
If the code reappears, call for service.
OEA fault is detected in the water level sensor.Call for service.
4E2This occurs when the temperature exceeds 50 degrees for over 8 seconds in the Wool and Delicates cycle.Call for service.
PEWhen position of the clutch can’t be detected.Call for service.
PE1After position of the clutch is detected, if the signal of the clutch hall goes wrong, an error occurs .Call for service.
AE6Commuication error between INVERTER PBA and MAIN PBA.Call for service.

Samsung WA40J3000A washer error codes

The Washer may display information codes to help you understand what is occurring with your Washer better.

CODE SYMBOLMEANINGSOLUTION
Hot LED FlashesLid is open when washer is running.Close the lid tightly and restart the cycle. If the code reappears, call for service.
Warm LED FlashesCommunication error between SUB PBA and MAIN PBA.Call for service.
Cold LED FlashesA button is not working properly.Call for service.
Tap Cold LED FlashesThe Water Level sensor is not working properly.
When the Tap Cold LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Call for service.
Extra Large LED FlashesYour Washer has tried to fill but was unsuccessful.
When the Extra Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Make sure the water faucets are open all the way. Check for kinked hoses.
Check the inlet screens on the fill hoses.
If you use a Flood Safety Device, remove the device and connect the water hoses directly to the unit.
Check if the hot water supply hose is connected.You must connect the hot water supply hose because hot water is supplied by the Auto Temperature Control (A.T.C.) function.
Large LED FlashesYour Washer has tried to fill but has not reached the proper water level.
When the Large LED is flashing, the washer drains for 3 minutes. During this time, the Power button is inoperative.
Call for service.
Medium LED FlashesA fault is detected in the water level sensor.Call for service.
Small LED FlashesYour washer is not draining. It can also mean that the unit senses a small clog while drainingDo the following:
1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.
Hot & Warm LEDs flashUnbalanced load prevented your Washer from spinning.Redistribute the load, and then press the Start/ Pause button.
Hot & Cold LEDs flashMotor not running properlyRestart the cycle by presssing the Start/Pause button. If the code reappears, call for service.
Hot & Tap Cold LEDs flashMems sensor is not working properly.Call for service.
Hot & Extra Large LEDs flashDoor lock is not working properlyClose the lid tightly and restart the cycle. If the code reappears, call for service.
Hot & Large LEDs flashDoor lock is not working properly.Close the lid tightly and restart the cycle. If the code reappears, call for service.
Hot & Medium LEDs flashThermistor is not working properlyCall for service.
Hot & Small LEDs flashThe temperature of the supplied water is so high.Ensure that the cold water tap and the hot water tap are connected correctly. If the code reappears, call for service.

Samsung Top Load WA52J8060A, WA52J8700A washer error codes

The washer may display information codes to help you understand what is occurring with your washer better.

CodeMeaning
1CThe WaterLevel sensor is not working properly.
• Check WaterLevel Sensor wire harness.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “1C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
3CCheck the motor for operation.
• Try restarting the cycle.
• If the problem continues, call for service
4CWater is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufficient water pressure.
• Make sure that the cold water tap and the hot water tap are properly connected.
• Clean the mesh filter as it may be clogged.
NOTE
When the washer displays “4C”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
4C2• Make sure the cold water supply hose is firmly connected to the cold water tap.
If it is connected to the hot water tap, the laundry may be deformed with some cycles.
5CWater is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending on the connection type.
• Clean the debris filter as it may be clogged.
• Make sure the drain hose is straightened all the way to the drain system.
• If the information code remains, contact a customer service centre.
9C1The electronic control needs to be checked (Over Voltage Error).
• Check the PCB and wire harness.
• Check if power is supplied properly.
• If the information code remains, contact a customer service centre.
9C2Low voltage detected
• Check if the power cord is plugged in.
• If the information code remains, contact a customer service centre.
AC6Inverter Communication problem
• Check the Inverter PCB and wire harness.
• If the information code remains, contact a customer service centre.
dCOperating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
HCHigh temperature heating check.
• If the information code remains, contact a customer service centre.
LCCheck the drain hose.
• Make sure the end of the drain hose is placed on the floor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service centre.
NOTE
When the washer displays “LC”, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
OCWater is overflowed.
• Restart after spinning.
• If the information code remains on the display, contact a local Samsung service centre.
PCWhen position of the clutch can't be detected.
• If the information code remains, contact a customer service centre.
PC1After position of the clutch is detected, if the signal of the clutch hall goes wrong.
• If the information code remains, contact a customer service centre.
UbSpinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a flat, stable surface.
• Redistribute the load. If only one item of clothing needs washing, such as a bathrobe or pair of jeans, the final spin result might be unsatisfactory, and an “Ub” check message will be 1. shown in the display