AEG washer error codes

AEG washer error codes

We use washers on a daily basis, that’s why it’s crucial to keep the device up and running. If you experience some technical problems with your AEG washer, don’t rush to call the service center – it is both costly and time-consuming. Everything can be fixed up on your own if you know how to perform diagnostics and maintenance. The process can take a few minutes, even if you’re not tech-savvy.

On this page, you can find the repair and maintenance guidelines for different models of AEG brand. They are made in the form of tables for your convenience: each table enlists the most widespread technical issues, all possible causes of malfunction, and possible solutions to the problems. Follow the step-by-step instructions to deal with issues.

Besides, you can find error codes for some washing machine models, such as LP 5280 and OKO LAVAMAT 6955. In devices of the AEG brand, there are eight major types of errors: the tables below present information about all of them.

Using these short guidelines you will be able to define the reasons of troubles and eliminate them shortly. If you still fail to fix the technical problems up, and the problem persists, don’t hesitate to call for a master. The guidelines below are taken from the official AEG washers’ manuals, but those may be not enough for fixing serious defects and irreversible mechanical or software damage.

AEG L 98690 FL washer error codes

ProblemPossible causePossible solution
The display tells to check the tap: the appliance does not fill with water.The water tap is closed.Open the water tap.
The water inlet hose is damaged.Make sure that the water inlet hose has no damages.
The filters in the water in- let hose are blocked .Clean the filters.
The connection of the water inlet hose is not correct.Make sure that the connection is correct.
The water pressure is too low.Contact your local water authority
The water tap is blocked or is furred with lime scale.Clean the water tap.
The display tells to check the drain filter: the appliance does not drain the water.The water drain hose is damaged.Make sure that the water drain hose has no damages.
The filter of the drain pump is blocked.Clean the filter of the drain pump.
The connection of the water drain hose is not correct.Make sure that the connection is correct.
The display tells to check the door.The appliance door is open or not closed correctly.Close the door correctly.
The display tells there is a water alert.The anti-flood device is activated.• Disconnect the appliance.
• Close the water tap.
• Contact the service centre.
The drum is empty and the display shows there is some weight in .It is necessary to set a tare.Press button 1 to deactivate the appliance and to activate it again.
The drum is full but the display shows 0.0 kg.You loaded the laundry before to activate the appliance.Press button 1 to deactivate the appliance . Empty the drum and obey to the necessary steps.

AEG LAVAMAT 50265 ELECTRONIC washer error codes

ProblemPossible causePossible solution
The door cannot be closed.The child safety feature is engaged.Release child safety feature
The indicator (END) flashes 4 times.The door is not closed properly.Close the door properly. Start the programme again.
The indicator (END) flashes once.The water tap is closed.Open the water tap.
Start the programme again.
The filter in the socket of the inlet hose is blocked.Close the water tap. Disconnect the hose from the water tap, remove the filter and clean under running water.
Water tap is blocked with limeseale or is faulty.Check the water tap and have it repaired if necessary.
The indicator (END) flashes 8 times.The programme selector has not clicked into place correctly.First turn the programme se- lector to O (OFF), then set the desired programme to the exact position.
The indicator (END) flashes twice.The drain pump is blocked.Switch off the machine and disconnect the mains plug. Clean the drain pump.
For siphon attachments: the siphon is blocked.Clean the siphon.
The door cannot be opened when the washing machine is on. (START/ PAUSE) and (DOOR) lights come on.Wait until the programme has ended, the (DOOR) light goes off and the (END) light is lit.
Door is locked due to high water level, or high temperature.If it is necessary to open the door immediately,
Turn the programme selector to (OFF); then turn it to (DRAIN). Press the (START/PAUSE) button.
When the water has been pumped out, the door can be opened.

AEG LAVAMAT 60640 washer error codes

Problem/ Possible causeSolution
The washing machine does not start:
The door has not been closed. E40
Close firmly the door.
The machine does not fill:
The water tap is closed. E10
Open the water tap.
The machine does not fill:
The inlet hose is squashed or kinked. E10
Check the inlet hose connection.
The machine does not fill:
The filter in the inlet hose is blocked. E10
Clean the water inlet hose filter.
The machine does not empty and/or does not spin:
The drain hose is squashed or kinked. E20
Check the drain hose connection
The machine does not empty and/or does not spin:
The drain pump is clogged. E20
Clean the drain pump.

AEG LP 5280 washer error codes

The display shows code:Possible cause
EXOThe mains supply is unstable. Wait until the mains supply is stable
EFOThe anti-flood device is on. Disconnect the appliance and close the water tap. Contact the service centre
E10The appliance does not fill with water properly
E20The appliance does not drain the water
E40The appliance door is open or not closed correctly. Please check the door!
E91No communication between electronic elements of the appliance. Switch off and switch on again

AEG OKO LAVAMAT 6955 washer error codes

The display shows code:Possible cause
Multidisplay shows F1 and the lights beside START and 900 are flashing. Programme stops. This indicates that the water supply has been blockedis the water tap open?
is the mesh in the inlet hose blocked? If necessary, clean the mesh.
is the inlet hose kinked?
To cancel the display message and restart the programme once water supply is restored, press START button.
If the fault re-occurs, close water supply and unplug the appliance. Contact Customer Service Department for advice.
Multidisplay shows F2 and the lights beside START and 1000 are flashing. Programme stops. This indicates that the water outlet has been blockedis the pump blocked? Remove any debris that is causing the blockage.
is the outlet syphon blocked? Clean if necessary
is the drain hose kinked?
has the recommended drain pump head of 1 metre height been ex- ceeded? If so, contact Customer Service Department for advice
To cancel the display message and restart the programme once block- age has been cleared, press START button.
If the fault re-occurs, close water supply and unplug the appliance. Contact Customer Service Department for advice