Asko washer error codes

Asko washer error codes

Asko Allergy W6888 washer error codes

Error messages Cause \ Solution
Wash motor faultCall the service division!
Overflow fault1. Shut off the water tap.
2. See Error messages "Water outlet fault"
Water outlet faultCheck:
• that no objects are stuck in the drainage hose outlet.
• that the drainage pump is not blocked by foreign objects. Clean the pump.
• that there are no kinks in the drainage hose. After taking measures, run the Drain program or press the Door opening button (key symbol) to empty the machine. If this does not resolve the problem, call the service division
Security faultCall the service division!
Water inlet faultCheck:
• that the tap on the water pipe is open.
• that the filter in the machine’s water inlet is not blocked.
Action:
1. Shut off the water tap.
2. Unscrew the hose.
3. Clean the filter in the inlet valve on the machine.
4. Screw the hose back on.
5. Turn on the tap and check for leaks.
6. Run the program again to check if the fault is fixed.
7. If this does not resolve the problem, call the service division
Close the DoorClose the washer door and the program will start
UnbalanceThe machine stops the spin cycle if there is too much imbalance. The washing machine restarts the spin cycle and hopefully the washing is better distributed in the drum. This procedure can be repeated up to 10 times. If the machine still fails to find a good balance, the program jumps to the next step

Asko W6122 washer error codes

ERROR MESSAGESOLUTION
NOTE: If an error occurs while a programme is running, the red fields around the buttons flash in slightly different ways. In order to exit error message status after implementing the measures below, turn off the machine. The error messages that may be shown are:
If L1 is flashing - The door is not closedIf L1 is flashing, you tried to start a programme with the washer door open. Close the door and the programme will start.
If L3 is flashing - Drainage errorIf L3 is flashing, there is a problem with drainage.
Check:
- that no objects are stuck in the drainage hose outlet.
- that the drainage pump is not blocked by foreign objects. Clean the pump
- that there are no kinks in the drainage hose.
After implementing corrective action, run the Drain programme or press the Key button (door open) to empty the machine. If this does not help, call the service division.
If L4 is flashing - Water intake errorIf L4 is flashing, there is a problem with the water supply.
Check:
- that the tap on the water pipe is open.
- that the filter in the machine’s water intake is not blocked.
1. Shut off the water tap.
2. Unscrew the hose.
3. Clean the filter in the intake valve on the machine.
4. Screw the hose back on.
5. Turn on the tap.
6. Run the programme again to check if the fault is fixed.
7. If the fault remains, call the service division.
If L6 is flashing - Door opening errorIf L6 is flashing, call the service division.
Overfilling - If all the red fields around the Start/Stop and Key buttons (door open) are flashing, there is too much water in the machine.
1. Shut off the water tap.
2. Call the service division.

Asko W6641 W661 washer error codes

ERROR MESSAGESOLUTION
"- - -"When this symbol flashes at the lower right corner of the display it merely means the glass door isn’t closed securely. Close the door and try again.
0If this message flashes at the top right of the LCD window, the machine has failed to spin. This could be because the load is out of balance. Turn the power off then on again. Open the door and redistribute the washing. Run the Spin program again.
Door lock faultCall a service technician.
FoamingRun the Rinse program again.
Try using less detergent and softener.
Use low-sudsing detergents.
OverflowCall a service technician
Pressure sensor fault
Temperature stop fault
Thermistor fault
Wash motor fault
Water inlet faultMake sure the water tap is open.
Water outlet faultCheck the pin trap for possible blockage. Make sure the outlet hose isn’t kinked.

Asko WM75.1 washer error codes

ErrorError indication on the display unitWhat to do?
E1THERMISTOR ERROR Temperature sensor error.• Inlet water too cold. Repeat the washing program.
• If the appliance reports this error again, call a service technician.
E2DOOR LOCK ERRORRestart the program. If the error reoccurs, call a service technician.
E3WATER FILLING ERRORCheck the following:
• is the water inlet valve open,
• is the filter on the water inlet hose clean,
• is the water supply hose deformed (clipped, clogged etc.).
Then, press the START button to resume the program. If the error reoccurs, call a service technician.
E6HEATING ERROR Water heating error.Restart the program. If the error reoccurs, call a service technician.
E7DRAINING ERROR Water draining error.Check the following:
• is the pump filter clean,
• is the drain hose clogged,
• is the drain clogged,
• is the drain hose fitted at the right height
Then, press the Start button again. If the error reoccurs, call a service technician.
E7.1DRAIN SYSTEM ALERT Water drain system alert.Alert about reduced water flow in the pumping stage. Check the following:
• is the pump filter clean,
• is the drain hose clogged,
• is the drain clogged,
• is the drain hose fitted at the right height
E10WATER LEVEL SENSOR ERRORRestart the program. If the error reoccurs, call a service technician.
E3WATER FILLING ERRORCheck the following:
• is the water inlet valve open,
• is the filter on the water inlet hose clean,
• is the water supply hose deformed (clipped, clogged etc.).
Then, press the START button to resume the program. If the error reoccurs, call a service technician.
E6HEATING ERROR Water heating error.Restart the program. If the error reoccurs, call a service technician.
E11OVERFLOW Water overflowing.Restart the program. If the error reoccurs, call a service technician.
E12MOTOR ERRORRestart the program. If the error reoccurs, call a service technician.
E22DOOR LOCK ERROR Error while locking the door.Door is closed, but it cannot be locked. Close the door again. Turn the washing machine off, then restart the washing program. If the error reoccurs, call a service technician.
E23DOOR UNLOCK ERROR Error while unlocking the door.Door is closed, but it cannot be unlocked. Turn off the washing machine, then turn it back on. If the error reoccurs, call a service technician.
E36COMMUNICATION Ul AND PMCU Error in Ul and PMCU communication.Turn off the appliance and turn it back on. If the error reoccurs, call a service technician.
UNBALANCEManually distribute the laundry and run the spinning program.
Unevenly distributed laundry.
STERIL TUB ALERT Warning - Self-cleaning programUse the self-cleaning program (DRUM CLEANING);