Maytag Washer Error Codes

The Maytag company was based in 1893 in Iowa by Frederik Maytag, the hereditary German. Initially, the firm specialized in producing of agricultural machinery. In 1902, the enterprise became the world`s leader in a number of released harvesting combines.

Maytag Washer Error Codes

But demand on brand`s production was seasonal. Frederik Maytag decided to turn the company`s engineering potential on developing and launching the washers` production. Initially, it was a construction with a grip for mechanical rotation. Further, the modernized and improved machine was designed with a drive and engine. In 1949, the firm released the fully automatic washer. Nowadays Maytag is a large international corporation with a mastered production in several countries around the globe.

Contemporary washers of Maytag brand are functional and reliable domestic technique. It equipped with automatic fault diagnosis system. The machine uses the special code to inform the consumer about the problem. The table, filled with the error codes of Maytag washers, is presented on the page below.

It is easy to use:

  1. In the left column of the table find the appropriate code, indicated on the display of your washer.
  2. In the line, you may find out about the reason of failure what is very important for understanding the problem.
  3. Now you can learn about the ways of solution. It can be the one simple action or several successive steps. It depends on the complexity of the situation.

Maytag 2000 Series (front-loading automatic) Washer Error Codes

An error code may be shown in the Estimated Time Remaining display. Check the list below for potential problem and troubleshooting checks.

CodesSolution
“LF” on display (Long Fill - no water or insufficient water supply)Press POWER/CANCEL to cancel the cycle. Unplug washer or disconnect power.
Plug in washer or reconnect power. Re-select cycle and press START/PAUSE. If the problem remains, call for service.
“F9E1” on display (Drain Problem)
Press POWER/CANCEL to cancel the cycle. Unplug washer or disconnect power.
Plug in washer or reconnect power. Re-select cycle and press START/PAUSE. If the problem remains, call for service
“SD” on display (Suds Routine)When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. “SD” is displayed during rinsing and at the end of the cycle to inform you that the Suds Routine was activated. Use only HE (High Efficiency) detergents.
“F--E--” Variables (Washer Problem)
Press POWER/CANCEL to cancel the cycle. Select RINSE, DRAIN & SPIN if there is excessive water in the washer. Re-select cycle and press START/PAUSE. If the problem remains, call for service.

Maytag Neptune 27” front load Washer Error Codes

LED Display DescriptionDiagnostic code
(Value refer to the table below)
nd The water level fails to drop below the Low Water level reset within 15 minutes, before a spin begins.1
LODoor failed to unlock after 3 attempts.2
nFContinuous fill of 12minutes. Total fill of 14minutes. 3
FLDoor failed to lock after3 attempts. 4
LEWater sensor level fault. 8
OEA fault is detected in the water level sensor. Data (frequency) shows the water level is at or above the overflow level.E
E2Detected a key pressed more than 30seconds, the key will be assumed to be stuck.15
dcNever exceeded 400rpm due to an unbalanced load.10
odThe door has not been opened after two complete wash cycles. Door switch was not seen open since the last two final spins.17
dLOpen door lock switch with motor running.18
dSDoor switch is read as open and the door locked switch is read as locked.22
bEMotor tach signal exists without motor running.25
tEAbnormal high/low temp or ohm resistance seen.29
E3Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving. (Locked, Hall Sensor fault)2E
SrSystem Relay failure. 34
HrHeater Relay failure. 36
3EOver Current is detected. Motor won't turn. 3E
2EVoltage for motor control bus is over specified limit.91
2EVoltage for motor control bus is under specified limit.92


Diagnostic codeDescriptionTriggerAction to be taken
1No DrainThe water level fails to drop below the Low Water level reset within 15 minutes, before a spin begins.Displays «nd».
2The door fails to unlockDoor failed to unlock after 3 attemptsDisplays «LO».
3No FillContinuous fill of 12 minutes. Total fill of 14 minutes.Displays «nF».
4The door/lid fails to lockDoor failed to lock after 3 attemptsDisplays «FL».
5-7Not Used
8Water level sensor fault.Input signal from water level sensor is out of range, Washer will beep and pause the wash cycle.Displays «LE».
9Not Used
10Unbalance or cabinet hit detected during final spin, which prevented the spinner from exceeding 400 rpmNever exceeded 400 rpm due to an unbalanced load.Will display «dc».
EWater sensor level fault.Water level in the machine is believed to be above the overflow level. When this condition is detected, the machine will automatically begin pumping water out until it falls below the overflow level.First check to see that water valve is not stuck. If water valve is OK, check water level sensor.
11Will not remember machine settingsDifficulty in reading memoryDisconnect and reconnect the washer power cord at power supply outlet. If condition still exists, replace machine control board.
12-14Not Used
15Stuck KeyA key is sensed to be pressed more than 30 seconds, the key will be assumed to be stuck.Display «E2». Check connection of keypad to control board. Replace console if necessary.
17Door/Lid switch was not seen open since the last two final spinsThe door has not been opened after two complete wash cycles. Door switch was not seen open since the last two final spins.Will display «od». If door open sensed, error will clear. Check door lock.
18Detected door lock switch open during cycle when not expected.Open door lock switch with motor running.Check for loose wire connections. Clear the diagnostic code and recheck; if reoccurs. Check door lock system. Check the output voltage of door lock coil. If normal, change door lock switch. If not normal, change Machine Control Board.
19-21Not Used
22Door/lid switch detected open during cycle (when not paused).Door switch is read as open and the door locked switch is read as locked.
23-24Not Used
25Motor tach signal exists without motor running.Tach signal exists without torque command or when not expected.Displays «bE». Replace Motor Control Board.
26-28Not Used
29Sump thermistor failure (Optional)Abnormal high/low temp or ohm resistance seenDisplays «tE»
- Loose or pinched wires.
- Bad sump thermistor.
30-33Not Used
2EMotor Drive failure (Locked, Hall sensor fault)Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving.Display «E3» Evaluate wire harness for loose or unhooked connections. If machine has separate motor control, perform self diagnostic motor test.
34System Relay failureMachine control does not see relay open when it should.Display «Sr». Replace machine control board.
35Not Used
3EMotor failure (Over current)Over Current is detected. Motor won't turn.Displays «3E».Check the motor windings, the speed sensor, wiring connections, or Control Board.
40-49Not Used
91Voltage for motor control bus is over specified limitVoltage for motor control bus is over limitDisplay «2E». Replace Machine Control Board.
92Voltage for motor control specified limitVoltage for motor control bus is under specified limit.Display «2E». Replace Machine Control Board.

Maytag FAV6800A Series Washer Error Codes

LED DisplayDescriptionDescription
CLClosed: Lid is closed.For a detailed error code, see the table below
dcDistribute Clothes: The load is unbalanced, preventing high speed spin. Redistribute clothes.
FLFailed to Lock: The machine has repeatedly tried to lock the lid. Make sure the lid is shut completely.
LOLocked: Lid has failed to unlock - the machine has repeatedly tried to unlock the lid. Push lid closed to make sure nothing from the inside is pressing against the lid, preventing unlocking.
LrLocked Rotor: The machine has repeatedly tried to turn the motor.
ndNo Drain: The machine has tried to drain.
OPLid is Open: Make sure it is fully closed before starting cycle.
odOpen the Lid: The lid has not been opened for the last three completed cycles.
nFNo fill: the machine has tried to fill.
PFPower failure: Power to the machine has been lost during the last cycle. This may also occur on start up of a new machine due to factory testing. Check the lid. Press any key to return the display to normal activity.
SdSuds: Machine has detected high level of suds. The machine will alter its cycle for this situation. Use hE detergent or reduce the amount of detergent.
ULLatch Unlocked: Close lid tightly to enable locking.
UCContinuous Unbalanced Circuit. Improper signal from Tub Displacement Sensor. Check Pressure Switch before replacing Tub Displacement Sensor
UBUnbalance or cabinet hit detected during final spin, which prevented the spinner from exceeding 500 rpm
LLLarge Load Detected
CLClear To Reset Cycle Counts
oLMachine Paused-Load Wedging

Diagnostic codeDescriptionTriggerAction to be taken
1No DrainThe water level fails to drop below the Low level before a spinDisplays "nd" Go to "Will Not Drain”
2The lid fails to unlockLid failed to unlock after multiple attemptsDisplays "LO" Go to "Will Not Unlock"
3No FillTotal fill 14 minutes exceeded.Displays "nF". Go to "No Water Fill"
4The lid fails to lockLid failed to lock after 11 attemptsDisplays "FL" Go to "Will not unlock"
5Continuous unbalanced circuit. Out of balance circuitUnbalanced loadDisplays "UC" Go to "Wet Clothes"
6Locked Rotor forcing a shut down.Locked rotor is still locked after 10 attempts.Displays "Lr" Go to "Motor Control Board Output Test"
8Water level sensor fault.Input signal from water level Sensor is out of range, Washer will beep and pause the wash cycle.Displays "LE" Go to “No water fill troubleshooting”.
10Unbalance or cabinet hit detected during final spin, which prevented the spinner from exceeding 500 rpmLess than 500 rpm due to an unbalanced load.LED-Will display “ub". Go to "Wet Clothes"
11Will not remember machine settingsDifficulty in reading memoryGo to "Clear diagnostic codes"
Disconnect and reconnect the washer power cord at power supply outlet.
If condition still exists, replace machine control board.
15Stuck KeyDetected a key pressed more than 75 seconds. The key is assumed to be stuck.Go to "Membrane Pad Check"
Check connection of keypad to control board.
Replace console if necessary.
16High speed not achieved due to torque.Speed less than 400 rpm during a main wash cycle.Go to "Wet Clothes"
17The lid was not opened after completed wash cycles.Did not sense lid open after the last three completed cycles.LED-Will display “od”. Customer may have tried to repeat wash cycle without opening the lid. Go to "Lid Lock Test"
18Detected lid lock switch open during cycle when not expected.Open lid lock switch with motor running.Check for loose wire connections. Clear the diagnostic code and recheck; if reoccurs, perform Diagnostic Motor/Motor Control Board test Check for faulty motor relay on the machine control board.
22Detected lid switch open during cycle (when not paused).Detected lid sensor switch open and the lid locked switch locked.Go to "Lid Lock Test"
23Lid is locked at start of cycleLid lock is locked and a user tries to start a cycle.Go to ‘Will Not Unlock"
24Motor high RPM detected two timesMotor tach signal is seen at maximum speed.Replace motor control board.
25Motor tach signal exists without motor runningTach signal exists without torque input. (Abnormal condition only)
28Water valve thermistor failureAbnormal high/low temp or ohm resistance seenGo to "Wrong Water Temperature"
34Welded system relayChange of state of the relayDisconnect power. Continuity between p.6 pin 1 to p.8. pin 1 at the Machine Control Board connector.
40Washer not operating due to tumble not functioningLoad bound up.LED-Will display “oL”. The washer is unable to complete its cycle. The paddles cannot move. To continue, separate and redistribute the load, then press “start/pause”.

Maytag BRAVOS XL MVWB750YW0 Washer Error Codes

If you experiencePossible CausesSolution
oL (overloaded) appears in displayLoad too large.If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent. Close lid and press START/PAUSE.
uL (unbalanced load) appears in displayLoad not balanced. The washer is running a load-balance correction routine.Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
LF (too long to fill) appears in displayWasher taking too long to fill. Drain extends more than 4.5" (114 mm) into standpipe.Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening.
Ld (too long to drain water) appears in displayWasher taking too long to drain water. Drain extends more than 4.5" (114 mm) into standpipe.Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor. Remove any clogs from drain hose.
HC (Hot and Cold hoses reversed) appears in displayHot and cold inlet hoses have been installed incorrectly.This code will appear at the end of the wash cycle to indicate that cold water hose is connected to the hot water inlet and hot water hose is connected to the cold water inlet.
Sd (Excess suds) appears in displayExcessive suds in washer. Washer is running a suds reduction routine.Allow the washer to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions. If the dial is flashing, reselect your desired cycle using a cold wash temperature, and press START/PAUSE. Do not add detergent.
dL (Lid cannot lock) appears in displayAn item in the load may be keeping the lid from locking.Check for items directly under the lid.
lid (Lid opened) appears in displayWasher lid left open.Close the lid to clear the display. If the lid is left open for more than 10 minutes, the cycle will reset and water in the washer will drain.
dU (Lid cannot unlock) appears in displayObjects on washer lid prevent it from unlocking.Remove objects, such as a basket of laundry, from the top of the washer.
F## code (F-type error code) appears in displaySystem error code.Press START/PAUSE once to clear the code. Then press START/PAUSE again to restart washer. If code appears again, call for service.
Fd (Factory Default) VWasher sets back to factory default.To return all options and modifiers to Factory Default, press POWER/CANCEL, select RINSE/DRAIN & SPIN cycle, and then press EXTRA RINSE, FABRIC SOFTENER, EXTRA RINSE, FABRIC SOFTENER within 5 seconds. When done correctly, the display shows “Fd” for 3 seconds and then unit returns to Standby Mode. y

Maytag Bravos W10092822A0 Washer Error Codes

CodesCauses/SOLUTION
Maytag Bravos W10092822A0 Washer Error Codes
"LF"
(Washer is taking too long to fill)
Check the following:
Are the hot and cold faucets turned on?
Are the water inlet hoses kinked or clogged?
Are the water inlet valve screens clear?
Press POWER/CANCEL to clear display.
Maytag Bravos W10092822A0 Washer Error Codes
"Ld"
(Washer is taking too long to drain water from the wash tub)
Check the following:
Is the drain hose kinked or clogged?
Is the drain hose installed properly?
Press POWER/CANCEL to clear display.
Maytag Bravos W10092822A0 Washer Error Codes
"uL"
(Unbalanced Load)
If the load is unbalanced, the washer will display this code while running an imbalanced load correction routine at the end of the wash cycle and before the final spin. If the code remains and the wash cycle dial is flashing after the recovery routine has stopped, open lid and redistribute the load. Close lid and press START/PAUSE.
NOTE: For best performance, load garments in loose heaps evenly around the basket wall. Do not load above the stainless steel portion of the basket.
Maytag Bravos W10092822A0 Washer Error Codes
"oL"
(Over Load)
Is the washer overloaded? The washer has attempted to fill and begin the wash cycle. If the washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START/PAUSE.
Maytag Bravos W10092822A0 Washer Error Codes
"Sd"
(Suds Detected)
Did you use regular detergent?
Regular or non-HE hand-washing detergents are not recommended for this washer.
Maytag Bravos W10092822A0 Washer Error Codes
"lid"
(Lid Opened)
Is the lid open? Close the lid to clear the display. If the lid remains open for more than 10 minutes, water in the wash tub will drain.
Maytag Bravos W10092822A0 Washer Error Codes
"HC"
(Cold and Hot hoses switched)
This code will appear at the end of the wash cycle to indicate that the cold and hot water inlet hoses are switched.
Maytag Bravos W10092822A0 Washer Error Codes
"dL"
(Door/Lid cannot lock)
Indicates lid is not locked. Check for items caught in the lid keeping it from closing. Press POWER/CANCEL once to clear the code.
Maytag Bravos W10092822A0 Washer Error Codes
"dU"
(Door/Lid cannot unlock)
Is there excessive weight on the lid, such as a basket of laundry? Excessive weight will keep the lid from unlocking. Press POWER/CANCEL once to clear the code.
Maytag Bravos W10092822A0 Washer Error Codes
"F##"code
Press POWER/CANCEL once to clear code. Press START/PAUSE to continue cycle. If code appears again, call for service.
Maytag Bravos W10092822A0 Washer Error Codes
"Fd"
(Factory Default)
This code will appear when your washer sets back to factory default.
To return all options and modifiers to Factory Default, press POWER/CANCEL, select Drain & Spin cycle, and then press Extra Rinse, Fabric Softener, Extra Rinse, Fabric Softener within 5 seconds. When done correctly, the 7-segment displays show "Fd" for 3 seconds and then unit returns to Standby Mode.

Maytag AFFRESH W10176966D Washer Error Codes

CodesCauses/SOLUTION
"F20" (Water Inlet Problem—no water or insufficient water supply)Select POWER/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
Are both hot and cold water faucets completely turned on?
Are screens at inlet hose connection to washer clogged?
Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug in washer or reconnect power. Re-select cycle and press START/PAUSE. If the problem remains, call for service.
"F21" (Drain Problem)Select POWER/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96" (2.4 m) above the floor?
Plug in washer or reconnect power. Re-select cycle and press START/PAUSE. If the problem remains, call for service.
"SUD" (Suds Routine)When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. "SUD" is displayed during rinsing and at the end of the cycle to inform you that Suds Routine was activated. Use only HE (High Efficiency) detergents.
"F22" (Front Door Lock)Select POWER/CANCEL twice to cancel the cycle.
Check the following:
Is the washer door firmly shut?
The door must be completely closed for the washer to operate. The door may look closed, but may not be latched. Open the door and close firmly.
Were you washing a large load?
Before you close the washer door, check that clothes are inside the washer drum and away from the seal area so the clothes can tumble freely. An overloaded basket may keep the door from closing completely. Reduce your load size if needed. Close the door.
Press POWER/CANCEL and then press START/PAUSE.
"F" Codes other than F20, F21, or F22Select POWER/CANCEL twice to cancel the cycle. Select DRAIN & SPIN if there is excessive water in the washer.
Re-select cycle and press START/PAUSE. If the problem remains, call for service.
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the washer door firmly closed?
Has a cycle been selected, but START/PAUSE has not been selected and held for 1 second?
Was the door open after completion of last cycle?

Maytag MAT12CS Washer Error Codes

CodesCauses/SOLUTION
d1Water level detection error on control board or due to power line interference (cycles and customer display disabled until diagnostic code is manually cleared).
d3Water temperature sense error when equipped with temperature sensing water valve (cycles will fill with unregulated default water temperatures while the error persists).
d4Washer lid sense error on control board or due to power line interference (cycles and customer display disabled until diagnostic code is manually cleared).
d5Blocked coin 1 or coin drop control circuit failure (coin recognition and price display disabled while blockage persists). PN MODELS ONLY: Make sure cycle price is selected to zero and coin option is not selected. (Set-up mode 6 should be set to 00 for free cycle operation. Set-up mode J. should be set to_d to prevent coin drop diagnostic codes.)
d7Last fill was slow.
d8Last drain occurring during final spin was slow.
d9Voltage detected below 180 vac for 8 seconds.
d12Motor sense error detected on control board or due to power line interference.
d13Blocked coin 2 or coin drop control circuit failure (coin recognition and price display disabled while blockage persists).

Maytag MAH14PD Washer Error Codes

CodesCauses/SOLUTION
d4Washer door sense error on control board or due to power line interference (cycles and customer display disabled until diagnostic code is manually cleared).
d5Blocked coin 1 or coin drop control circuit failure (coin recognition and price display disabled while blockage persists). PN Models Only (MAH 14): Set-up mode 6 should be set to 00 for free cycle operation. Set-up mode J. should be set to _d to prevent coin drop diagnostic codes.
d7Slow fill detected during previous cycle (cycle paused but can be re-started).
d8Last drain was slow.
d9Voltage detected below 90vac for 8 seconds.
d10Door lock sense error or due to power line interference (spins inhibited until corrected).
d11Motor speed error detected (cycle paused but can be re-started).
d13Blocked coin 2 or coin drop control circuit failure (coin recognition and price display disabled while blockage persists).
d16Not receiving communications from installed debit card reader in Generation 2 debit mode.

Maytag MAF9601 Washer Error Codes

Display showsExplanationSuggested remedy
Maytag MAF9601 Washer Error CodesOver flowCall service.
Maytag MAF9601 Washer Error CodesWash motor fault
Maytag MAF9601 Washer Error CodesWater outlet faultPumping fault; check:
- That no object is trapped in the outlet from the drain hose.
- That the drain pump is not blocked by foreign bo dies. Clean the pump.
- That the drain hose is free from kinks.
After performing the remedy, run the Drain program me. If this does not help, call service.
Maytag MAF9601 Washer Error CodesWater inlet faultWater supply fault; check:
- That the tap in the water pipe is open.
- That the strainer in the water inlet to the machine is not obstructed.
1. Close the water tap.
2. Unscrew the hose.
3. Clean the strainer in the inlet valve to the machine.
4. Screw back the hose.
5. Open the water tap.
6. Run the programme again to check that the fault has been remedied.
Maytag MAF9601 Washer Error CodesThermistor faultCall service.
Maytag MAF9601 Washer Error CodesTemperature stop fault
Maytag MAF9601 Washer Error CodesFoaming (this function is not available on all machines)Run the Rinse programme once. Check the detergent metering. Use a low-lather detergent.
Maytag MAF9601 Washer Error CodesDoor lock faultCall service.
Maytag MAF9601 Washer Error CodesMachine fails to spin.1. The machine has a built-in unbalance sensor, which causes the spin speed to be reduced or spinning to be bypassed if there is great unbalance in the load. Turn off the main power switch, and turn it on again. Open the door and redistribute the washing.
2. After performing the remedy, run the Spin program me.
Maytag MAF9601 Washer Error CodesYou have tried to start a programme with the door open.Close the door and try again.

Maytag MHWC7500YW Washer Error Codes

If you experiencePossible CausesSolution
A09 (Water Inlet Problem) appears in display and system will pauseNo water or insufficient water supply. Unplug washer or disconnect power.Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Check if water inlet hoses are frozen.
Plug in washer or reconnect power. Press and hold START to continue the cycle or press and hold CANCEL/DRAIN to cancel the cycle. If the problem remains, call for service.
A10 (drain pump system error) appears in displayUnplug washer or disconnect power.Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 55" (1.4 m) above the floor.
Not using HE detergent or using too much HE detergent.Use only HE detergent. Always measure detergent and follow manufacturer’s directions based on load size and soil level.
F01 - F30 appears in displayElectrical problem.Turn knob to OFF or press and hold START to cancel the cycle. Select DRAIN/SPIN if there is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call for service.

Maytag MHW6000XG0 Washer Error Codes

If you experiencePossible CausesSolution
Sud (Excess suds) appears in displayExcessive suds in washer. Washer is running a suds reduction routine.Allow the machine to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions.
F8E1 (water supply error) appears in displayCheck for proper water supply.Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Press POWER/CANCEL once to clear the code. Then press POWER/CANCEL again to restart washer. If code appears again, call for service.
F9E1 (drain pump system error) appears in displayCheck plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 4.5" (114 mm).Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.
Not using HE detergent or using too much HE detergent.Use only HE detergent. Always measure detergent and follow manufacture’s directions based on load size and soil level.
F5E2 (door will not lock) appears in displayWasher door not locking.Press POWER/CANCEL to cancel the cycle. Make sure the door is closed completely and latching. Check for items in the washer drum that may be keeping the door from closing completely.
F7E1 (motor drive error) appears in displayMotor is having difficulty turning the drum.Washer is overloaded. Remove some items.
Make sure that all shipping materials have been removed.
“rL” (remove load) appears in displayLoad detected in drum during Clean Washer with AFFRESH™ cycle.Remove items from drum and restart Clean Washer with AFFRESH™ cycle.
Washer making error beeps.Door has not been opened and closed for at least 3 cycles.This code may appear when the washer is first turned on. Open and close the door to clear the display.
Washer beeps when START/PAUSE is pressed.Door not closed.Close the door completely.
F#E# code other than as described above appears in display System error code.Press POWER/CANCEL once to clear the code. Then press POWER/CANCEL again to restart washer. If code appears again, call for service.

Maytag MHW7000A Washer Error Codes

If you experiencePossible CausesSolution
Sud (Excess suds) appears in displayExcessive suds in washer. Washer is running a suds reduction routine.Allow the washer to continue. Use only HE detergent. Always measure detergent, and base detergent quantity on load size. Follow detergent manufacturer’s instructions.
F08 followed by E01 (water supply error) appears in displayCheck for proper water supply.Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Touch POWER/CANCEL once to clear the code. Then touch POWER/CANCEL again to restart washer. If code appears again, call for service.
F09 followed by E01 (drain pump system error) appears in displayCheck plumbing for correct drain hose installation. Drain hose extends into standpipe farther than 4Vi" (114 mm).Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.
Not using HE detergent or using too much HE detergent.Use only HE detergent. Always measure detergent and follow manufacturer’s directions based on load size and soil level.
F05 followed by E02 (door will not lock) appears in displayWasher door not locking.Touch POWER/CANCEL to cancel the cycle. Make sure the door is closed completely and latching. Check for items in the washer drum that may be keeping the door from closing completely.
F07 followed by E01 (motor drive error) appears in displayMotor is having difficulty turning the drum.Washer is tightly packed. Remove some items. recommendations. Make sure that all shipping materials have been removed.
“rL” (remove load) appears in displayLoad detected in drum during Clean Washer with affresh cycle.Remove items from washer drum and restart Clean Washer with affresh cycle.
Washer making error beepsDoor has not been opened and closed for at least 3 cycles.This code may appear when the washer is first turned on. Open and close the door to clear the display.
Washer beeps when START is touchedDoor not closed.Close the door completely.
F## E## code other than as described above appears in displaySystem error code.Touch POWER/CANCEL once to clear the code. Then touch POWER/CANCEL again to restart washer. If code appears again, call for service.
Int (interrupted) appears in displayThe cycle was paused or cancelled.The washer can take 20 to 30 minutes to stop spinning and drain and will display this error code during that time. Touch POWER/ CANCEL once to clear the code. Then touch POWER/CANCEL again to restart washer.

Maytag MAH9700AW* Washer Error Codes

Code Symbol
MeaningSolution
Maytag MAH9700AW Washer Error CodesUnbalanced load prevented the washer from spinning.Redistribute the load, press the Cycle Selector dial.
Maytag MAH9700AW Washer Error CodesDoor is unlocked when washer is running.Press Power Off pad then restart the cycle. If the code reappears, call for service
Maytag MAH9700AW Washer Error CodesDoor is open when washer is running.Close the door tightly and restart the cycle. If the code reappears, call for service
Maytag MAH9700AW Washer Error CodesThe washer failed to lock the door.
Maytag MAH9700AW Washer Error CodesWater temperature control problem (Heater Control problem)Call for service
Maytag MAH9700AW Washer Error CodesThe washer has tried to fill but has not reached the proper water level.
Maytag MAH9700AW Washer Error CodesThe door will not unlock.Make sure the door is firmly closed. Push the Power Off pad to turn off the washer, and then turn it on using any pad. If the code reappears, call for service
Maytag MAH9700AW Washer Error CodesMotor not running properly.Restart the cycle pressing the Cycle Selector dial. If the code reappears, call for service
Maytag MAH9700AW Washer Error CodesThe washer is not draining.Call for service
Maytag MAH9700AW Washer Error CodesThe washer has tried to fill but was unsuccessful.Make sure the water faucet are open all the way. Check for kinked hoses. Check inlet screens on fill hoses.
Maytag MAH9700AW Washer Error CodesProblem with control.Call for service
Maytag MAH9700AW Washer Error CodesElectric service was lost when washer was running.Restart the cycle by pressing the Cycle Selector dial.

Maytag NEPTUNE TL Washer Error Codes

Code SymbolMeaningSolution
Maytag NEPTUNE TL Washer Error Codes
"FL"
The washer failed to lock the lid.Make sure nothing is obstructing the lid. Close the lid and restart the cycle.
Maytag NEPTUNE TL Washer Error Codes
"PF"
The washer experienced a power failure.Restart the cycle. If code is still displayed, check to make sure power cord is securely plugged in.
Maytag NEPTUNE TL Washer Error Codes
"nd"
The washer experienced difficulty draining.Check for a kinked drain hose. Check for a plugged stand pipe.
Maytag NEPTUNE TL Washer Error Codes
"LO"
The washer has repeatedly tried to unlock the lid but has been unsuccessful.Make sure lid is firmly closed. Push the “Off” button and then wait four minutes for the lid to unlock. OR Unplug the washer for two minutes and plug back in.
Maytag NEPTUNE TL Washer Error Codes
"Lr"
Motor not running properly.Call for service.
Maytag NEPTUNE TL Washer Error Codes
"nF"
The washer has tried to fill, but has not reached the proper fill level.Make sure the water faucets are open all the way.
Check for kinked hoses.
Check inlet screens on fill hoses.
Maytag NEPTUNE TL Washer Error Codes
"UC"
The washer cannot spin.Press Start/Pause to restart the washer and complete the cycle. If this problem persists, call for service
Maytag NEPTUNE TL Washer Error Codes
"dc"
Unbalanced load prevented the washer from spinning.Redistribute the load, then press Start/Pause.
Maytag NEPTUNE TL Washer Error Codes
"LL"
The washer cannot spin because the load is too large.Remove some items from the tub and press Start/Pause. If removing items does not correct the problem, call for service
Maytag NEPTUNE TL Washer Error Codes
"oL"
The washer cannot tumble because something is blocking the tumblers.Remove item from the tub. Press Start/Pause. OR
Remove part of the load from the washer. Press Start/Pause.
Maytag NEPTUNE TL Washer Error Codes
"OP"
The washer lid is open.The lid must be closed to start cycle. Close the lid and press Start/Pause.
Maytag NEPTUNE TL Washer Error Codes
"od"
The washer lid must be opened.This is a safety feature. The lid must be opened before another cycle is started.
DODoor Open
Door monitor switch in door lock mechanism is not able to communicate to the control board is open
1. Make door is closed.
2. Check for loose wire connections at switch and/ or machine control board.
3. Check for failed door monitor switch.
4. Check inputs and outputs at machine control board.
5. Replace responsible component.
SdSuds
The machine has detected high levels of suds.
The machine will alter its cycle for this situation. Use an HE detergent or cut down on the amount of detergent slightly. This can be more likely on towel loads, consider HE detergent especially for these loads.

Maytag Maxima washer error codes

Error CodeConditionCheck/RepairShop Parts
SUDSExcessive sudsIf you see excessive suds in the washer, start using the right amount of high-efficiency (HE) detergent.(HE) detergent
F0E1Load detected during the washer cleaning cycleRemove clothes from the washer. The washer must be empty when running a washer cleaning cycle.
F1E1Main control board failureTry to reset the control board by unplugging the washer for 5 minutes and then restoring power. If the F1E1 code returns after restoring power, replace the main electronic control board.Main control board 
F1E2Motor control board errorUnplug the washer. Check the wire harness connections on the motor control board. Make sure the drive motor connections are secure. If the wiring connections are okay, replace the motor control board.Motor control board 
F2E3Main control board mismatch or main control board failureThe code appears when you install the wrong main control board. Order and install the correct main control board for your washer. If the code appears when you're not replacing the main control board, then the main control board failed. Replace the main control board.Main control board
F3E1Water level pressure switch failureUnplug the washer. Check the wiring between the water level pressure switch and the main control board. Reconnect any loose wires. Replace the wire harness if damaged. If the wiring is okay, replace the water level pressure switch.Water level pressure switch, wire harness
F3E2Temperature sensor failureUnplug the washer and check the wiring going to the water temperature sensor. If the wiring is okay, replace the temperature sensor.Temperature sensor
F4E0Water heater failureUnplug the washer and check the wiring going to the water-heating element. If the wiring is okay, replace the heating element.Heating element
F5E1Door switch failureThis code appears if the control does not detect the door opening after 3 consecutive loads, indicating that the door switch failed. The code also displays when the door switch is open with the door locked. Replace the door lock/switch.Door lock/switch
F5E1Door switch failureThis code appears if the control does not detect the door opening after 3 consecutive loads, indicating that the door switch failed. The code also displays when the door switch is open with the door locked. Replace the door lock/switch.
F5E2Door lock failureThe door can't lock. Unplug the washer and check the door lock assembly for damage or a loose wiring connection. Clear any debris out of the door lock assembly. Replace the door/lock switch if defective.
F5E3Door unlock errorThe washer won't unlock. Unplug the washer and check the door lock assembly for damage or a loose wiring connection. Replace the door/lock switch if defective.
F6E1Communication error between the main control board and motor control boardUnplug the washer and check the wire harness connections between the main control board and the motor control board. Reconnect any loose wires. Replace the wire harness if damaged. Replace the motor control board is defective. If the problem persists, replace the main control board.Motor control board, main control board, wire harness
F6E2 or F6E3Communication error between the main control board and the user interface controlUnplug the washer and check the wire harness connections between the main control board and the user interface control. Reconnect any loose wires. Replace the wire harness if damaged. Replace the user interface control if defective. Replace the main control board is defective.User interface control, main control board, wire harness
F7E1Motor tachometer failureUnplug the washer and check the wiring between the motor control board and the drive motor. Check the wire harness connection between the motor control board and the main control board. Reconnect any loose wires. Replace any damaged wire harnesses. If the wiring connections are okay, check to see if the spin basket rotates smoothly. If not, resolve any friction issues in the drive system such as an obstruction caught between the spin basket and tub. If the spin basket rotates smoothly, replace the drive motor. If the problem persists, replace the motor control board.Drive motor, motor control board, wire harness
F7E2Motor or motor control board overheatedOverloading the washer can cause this code to appear. Remove some clothes if you overloaded the washer. Friction in the drive system also overheats the motor or the motor control board. Remove any obstructions between the spin basket and the tub. Replace the tub bearing if it's worn or locked up. Replace the drive motor or motor control board if defective.Drive motor, tub bearing, motor control board
F8E0Steam valve failureCheck the water supply hoses for kinks. Check for a restricted screen in the water valves. Replace the steam valve if defective.Steam valve
F8E1No water detectedMake sure that both water supply valves behind the washer are fully open. In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it.Water valve assembly
F8E2Dispenser failureThe dispenser can't move into position. Unplug the washer and check the mechanical linkage on the dispenser housing. Repair or replace any damaged dispenser parts.Dispenser assembly parts
F8E3Overflow conditionUnplug the washer and, if the washer is overfilled, check the water valve assembly for proper shut-off of water flow. If the water valve assembly is defective, replace it. If the washer is empty when this error code appears, replace the water level pressure switch.Water valve assembly, water level pressure switch
F8E4Low water flowThe flow meter detects a long fill time. Make sure that both water supply valves behind the washer are fully open. In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it. If water flows normally, replace the flow meter.Water valve assembly, flow meter
F9E1Long drainRemove excess suds; the washer can't drain excessively sudsy water. Check your house drain system for a clog. Check the drain hose for kinks or clogs. Replace the drain pump if defective. If the washer drains properly, replace the water level pressure switch because it isn't accurately detecting the water level.Drain pump, water level pressure switch

Modern technique has improved capabilities and impeccable quality. Maytag washers of professional and domestic classes are in demand: an easy to control device due to its functionality makes washing a pleasant process that does not require your effort.

Breakdown of a washing machine is a very rare occasion and usually is caused by a poor quality of tap water. If there is a failure, Maytag washer’s display will show you an error code notifying you of a problem cause.

All Maytag washer models with a display are equipped with the function of displaying an error code in case of some malfunctions and breakages. If you know the meaning of a certain error, you will be able to eliminate the damage by your own without calling a specialist. However, it is only about the most elementary errors. For example, for many washers, the 4E error code means the problems with supplying of water. Usually, it appears because of lack of water in a plumbing.

But the same code is shown in more complicated situations:

  • Contacts and connections of the priming valve.
  • There is a foreign object in the filling valve.
  • The inaccurate connection of cold and hot water – they are connected in reverse.
  • The connection of a liquid hose to a detergent container is broken, for example, the hose is pinched or torn.

Similar situations happen with other codes. Remember, if you know how to decipher an error, you will be able to solve the problem by your own (that is only for slight damages). But in most cases, the error codes of the Maytag washers, encrypted with a specific code, are for professionals who could repair the failed device.